Philips VRZ220AT, VRZ250AT owner manual Plug in the TV and the VCR, CH3

Page 7

VRZ220/250 layout 4/8/99 10:11 PM Page 7

Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

	AUDIO		ANT
	AUDIO		IN
		L	IN
		L
	OUT	IN
		R
	VIDEO		OUT
	VIDEO
	OUT	IN CH3	CH4

AUDIO		ANT
AUDIO		IN
	L
OUT	IN
	R
VIDEO		OUT
OUT	IN CH3	CH4

75V
ANT	/
CABLE

	ANTENNA IN Jack
	(on back of TV)
RF coaxial cable	example only
RF coaxial cable

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

ANT

AUDIOIN

L

OUT IN

AUDIO		ANT
AUDIO		IN
	L
OUT	IN
	R
VIDEO		OUT
OUT	IN CH3	CH4

R

VIDEO

OUT

CH3 CH4

OUT	IN CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Contents VRZ220AT VRZ250AT For Customer Use Dear Philips Magnavox product ownerIntroduction FeaturesTable of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemCH3 Plug in the TV and the VCRConnections Hookups With a Cable Box / Direct Broadcast SystemRecording/Viewing Any Channel Cable Box/DBS Recording One Channel/Watching AnotherRF coaxial Cable TV’s Antenna Jack VRZ250 Hookups With a Stereo TVVRZ220 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsYou make each entry within 60 seconds of the previous entry Follow the steps below to set your VCR’s clock. Make sureDaylight-Saving Time Language Selection Menu Button Remote Control ButtonsPower Button Time Search Button VRZ250 onlyClear Button Remote Control Buttons cont’dEject Button Press to eject the tapeIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR RecordingPress the VCR/TV button to put the VCR in VCR posi Remote control to select channel 03 or 04 at the TVRecording One Channel/Watching Another To return to the channel being recorded, use the TVOne-Touch Recording Set up the channels at the VCRDaily Timer RecordingSlots will flash on-screen Timer Recording cont’dStandard Play Press the STATUS/EXIT button. Program WAS COMTape Speeds Tape Speed Maximum Record/Playback Time Type T160 T120 T60Program REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsPress the PLAY/o button or the STOP/p button to select PROGRAM, then press the F.FWD/B buttonRerecording Tape Duplication Channel the CH3/CH4 switch on VCR 2 is set toTurn on the TV and set it to channel 03 or 04, whichever Press the F.FWD/B button so that on appears beside Repeat PlayPress the Time Search button Time Search VRZ250 onlyReal-Time Counter Memory Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Or Receiver Understanding On-Screen DisplaysMono MonitorMulti-Channel Television Sound System VRZ250 only cont’d Please see additional notes on Hi-Fi Stereo Sound System VRZ250 onlyHi-Fi Stereo Sound System VRZ250 only cont’d Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyIndex Supplied Accessories