Philips VRB664AT On-Screen Status Displays, Status Display example only, If you select Status OFF

Page 26

26 On-Screen Status Displays

A status display will appear when you press the STATUS/EXIT but- ton or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below.

If you select STATUS ON, then select COUNTER ONLY ON:

● Whenever you press the STOP/p button or the PLAY/o button,

the status display will appear for five seconds. After five seconds,

only the counter will remain on the screen. You must press the

STATUS/EXIT button to remove it. Portions of the status display

Status Display (example only)

Receiving and Recording Mode

also may appear when you press other function buttons.

If you select STATUS ON, then select COUNTER ONLY OFF:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the sta- tus display also may appear when you press other function but- tons.

If you select STATUS OFF:

Current status of tape

STOP

TV STEREO

Channel

Time

12:00 AM CH10

STEREO 2ND AUD

●The status display will not appear when you press function but- tons. You must press the STATUS/EXIT button to see the status display.

1

Press the VCR button, then press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select ON SCREEN MODE, then press the F.FWD/B button.

4

Press the PLAY/o button or the STOP/p button to select STATUS, then press the F.FWD/B button so that OFF (or ON) appears beside STATUS.

SELECT op CHOOSE B

→ STATUS	[ON]
COUNTER ONLY	[OFF]

TO END PUSH EXIT

5

If you set STATUS to OFF, go to step 6. If you set STA- TUS to ON, press the PLAY/o button or the STOP/p button to select COUNTER ONLY, then press the F.FWD/B button so that OFF (or ON) appears beside it.

6

Press the STATUS/EXIT button.

SLP M 1:23:45 HIFI

Tape	Counter	Audio
Speed	and	Out
	Counter	Mode
	Memory	MTS


		Broadcast
		Available

Helpful Hint

•You may not access a status display when viewing a still picture, during slow motion playback, or during for- ward or reverse searching.

Image 26

Contents VRB664AT Dear Philips product owner For Customer UseDeclaration of Conformity FeaturesIntroduction Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Hookups With a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups With a Stereo TV Turning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitInstructions continue on Manual Clock SettingDo each step within 60 seconds of the previous step Setting the Clock cont’d Enter a 0 before a single-digit numberAutomatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Menu Button REWind/ ButtonRECord/OTR Button Number ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording Turn on the TV and set it to channel 3 or 4, whichever chanOne-Touch Recording OTR CH12Recording One Channel/Watching Another Timer Recording DailyTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Checking or Cancelling Timer Recordings Setting Up the VCR Plus+ Programming System ChannelsSetting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System See page 58 for more hints Auto DBS RecordLink Set the clock. Details are on pagesRerecording Tape Duplication RF coaxial cablePress the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Automatic Operation Features Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture When Child Lock is activated Child LockSmart Picture Time Search Press the VCR button Press the Time Search buttonExample Press the VCR button Press the Index Search buttonRecord End Search Skip SearchReal-Time Counter Memory Blue Background Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onHelpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Video Cassette Recorder or PlayerPayment Amount Limited Warranty cont’dTo obtain a replacement product from Philips Payment, if applicableIndex AutomaticPage Page Page Supplied Accessories