Philips VRB664AT owner manual Timer Recording cont’d

Page 35

Timer Recording (cont’d) 35

4

Use the Number buttons (1-8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen.

NOTE: If you enter a number for a slot that has been used already to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly. Information about the program in that slot will appear on the screen. If this happens, press the STATUS/EXIT button, then select another number.

5

Use the Number buttons to enter the channel you want to record.

Cable Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. There also may be a brief delay when you select channels 10, 11, and 12. If you want to select channels 100 and above, enter channel numbers as a three-digit number. For exam- ple, to select channel 117, press 1, 1, 7.

Antenna Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay.

If you are recording from line input, press 0,0 to select AV REAR.

If you are using a Cable Box/DBS, enter the Cable Box/DBS out- put channel (03 or 04). Set the Cable Box/DBS to the channel you want to record. Leave the Cable Box/DBS on for the timer recording. See page eight for details.

4-7

POWER

 

EJECT

VCR/TV

SPEED

MEMORY

REC/OTR

 

PAUSE/STILL

 

PLAY

 

REW

 

F.FWD

 

STOP

 

MENU

STATUS/EXIT

CLEAR

1

2

3

 

4

5

6

CH.

 

7

8

9

 

MUTE

0

ALT.CH

VOL.

 

 

 

VCR

TV

CBL/DBS

 

 

 

VCR PLUS+

 

VAR.SLOW

/ENTER

SLOW

TRACKING

F.ADV

X2 PLAY

SMART

TIME

INDEX REC END

SKIP

PICTURE

SEARCH

6

Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

– : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

7

Follow the instructions in step 6 to enter the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

09:30 PM

TIME OFF

– : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

Instructions continue on page 36.

Helpful Hints

Entries that do not match the VCR’s clock or calendar will cause a ques- tion mark to appear on the screen.

If you are recording from line input, connect the audio and video cables to the AUDIO IN and VIDEO IN jacks on the back of the VCR. (Please see illustration on page 43.)

Image 35
Contents VRB664AT For Customer Use Dear Philips product ownerDeclaration of Conformity FeaturesIntroduction Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Recording One Channel/Watching Another Hookups With a Cable Box/Direct Broadcast System cont’dHookups With a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsInstructions continue on Manual Clock SettingDo each step within 60 seconds of the previous step Enter a 0 before a single-digit number Setting the Clock cont’dPress the VCR button, then press the Menu button Automatic Clock SettingTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Number Buttons REWind/ ButtonRECord/OTR Button Menu ButtonIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel VHS Quasi Play Back Sqpb PlayingTurn on the TV and set it to channel 3 or 4, whichever chan RecordingOTR CH12 One-Touch RecordingRecording One Channel/Watching Another Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Checking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System See page 58 for more hints Set the clock. Details are on pages Auto DBS RecordLinkRF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Automatic Operation Features Playing a Tape at Double Speed Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture Child Lock When Child Lock is activatedSmart Picture Press the VCR button Press the Time Search button Time SearchPress the VCR button Press the Index Search button ExampleSkip Search Record End SearchReal-Time Counter Memory Blue Background Understanding On-Screen Displays Multi-Channel Television Sound SystemMulti-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemHelpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Video Cassette Recorder or Player Limited WarrantyPayment, if applicable Limited Warranty cont’dTo obtain a replacement product from Philips Payment AmountAutomatic IndexPage Page Page Supplied Accessories