Philips VRB664AT owner manual Helpful Hints

Page 58

58 Helpful Hints

If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself.

If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is displayed on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative. If you believe the representative will need to help you with operations, please stay near the product. Our representatives will be happy to assist you.

No power

•Make sure the power plug is completely connected to an AC (alternating current) outlet.

•Make sure the power is turned on.

Power Failure

•With ShowGuard, if the power fails for more than one minute, programmed timer recordings will be restored when the clock is reset. (The clock will reset itself automatically if you are using the AUTO CLOCK feature. Details are on pages 17-18.If you are not using the AUTO CLOCK feature, reset the clock manually. Details are on pages 15-16.) The timer recording will not occur only if the timer record- ing was scheduled to take place during the power failure.

A TV program cannot be recorded.

•Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if applicable). Details are on pages six-10.

•Make sure the tape has a record tab. Details are on page five.

•Check the TV/VCR position. Details are on pages 24, 27, and 28.

•Check the CH3/CH4 switch. Details are on pages six-nine.

The VCR will not perform a timer recording.

•Make sure the recording start and stop times are set correctly. Details are on pages 34-41.

•Make sure a tape is in the VCR and the tape has a record tab (page five). If, after programming a timer recording, you turn off the VCR power without putting a tape in the VCR, the Timer light will blink.

•If the record tab on a tape is missing, the VCR will eject the tape. The Timer light will blink.

•Make sure the VCR power is off.

•Make sure the clock is set. Details are on pages 15-18.

•If you have a Cable Box/Direct Broadcast System, timer recordings are programmed differently. Details are on page eight.

•Finish programming a timer recording at least five minutes before the recording is set to begin.

•Noon is 12 p.m.; midnight is 12 a.m.

There is no playback picture or the playback picture is noisy or contains streaks.

•Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch.

•Make sure the VCR is in VCR position. (The VCR light will appear on the display panel.)

•Make sure channel 03 or 04 is properly adjusted at the TV.

•Adjust the tracking. Details are on page 45.

•TVs placed too close to the VCR can cause interference during tape playback. Move the VCR away from the TV.

The VCR cannot be controlled with the remote control.

•Press the VCR button, then try the other VCR feature buttons.

•Make sure the VCR light appears on the display panel. If it does not, press the VCR/TV button once.

•Aim the remote control directly at the VCR’s remote sensor. Details are on page 28.

•Remove all obstacles between the remote control and the VCR.

•Inspect and/or replace the batteries in the remote control. Details are on page five.

The VCR does not respond normally to the remote control. (For example, the VCR may change channels multiple times when you press the CH(annel) o button once.)

•Install new batteries (preferably alkaline) in the remote control.

The Number buttons won’t work for channels above 69.

•Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter chan- nel numbers as a three-digit number. Details are on page 25.

Page 57 Page 59
Image 58
Page 57 Page 59
Contents VRB664AT Dear Philips product owner For Customer UseIntroduction FeaturesDeclaration of Conformity Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast System cont’d Recording One Channel/Watching AnotherHookups With a Stereo TV Turning on Your VCR Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitDo each step within 60 seconds of the previous step Manual Clock SettingInstructions continue on Setting the Clock cont’d Enter a 0 before a single-digit numberAutomatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Menu Button REWind/ ButtonRECord/OTR Button Number ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing VHS Quasi Play Back SqpbRecording Turn on the TV and set it to channel 3 or 4, whichever chanOne-Touch Recording OTR CH12Recording One Channel/Watching Another Timer Recording DailyTimer Recording cont’d Press the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Checking or Cancelling Timer Recordings Setting Up the VCR Plus+ Programming System ChannelsSetting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System See page 58 for more hints Auto DBS RecordLink Set the clock. Details are on pagesRerecording Tape Duplication RF coaxial cablePress the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedViewing a Slow Motion Picture Viewing a Still PictureDuring tape playback, press the PAUSE/STILL button. a When Child Lock is activated Child LockSmart Picture Time Search Press the VCR button Press the Time Search buttonExample Press the VCR button Press the Index Search buttonRecord End Search Skip SearchReal-Time Counter Memory Blue Background Multi-Channel Television Sound System Understanding On-Screen DisplaysMulti-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes onHelpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Video Cassette Recorder or PlayerPayment Amount Limited Warranty cont’dTo obtain a replacement product from Philips Payment, if applicableIndex AutomaticPage Page Page Supplied Accessories
Top Page Image Contents