Philips VRB664AT Press the STATUS/EXIT button. Program WAS COM, See page 58 for more hints

Page 41

Timer Recording with the VCR Plus+ Programming System (cont’d) 41

5

Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. Your selection will appear beside REC SPEED on the screen; SP=1 SLP=2 will continue to flash. For details about tape speed, see pages 36 and 60. You cannot use the SPEED button at this time.

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	09
TIME ON	10:30 PM
TIME OFF	11:30 PM
REC SPEED	SLP
SP=1 SLP=2
START DATE	10/10/00
	TUE.

TO END PUSH EXIT

6

Press the STATUS/EXIT button. PROGRAM WAS COM-

PLETED/PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen briefly.

7

Press the POWER button to turn off the VCR power. The Timer light will appear. The Timer light will flash if there is not a tape in the VCR.

If the timer recording will take place several hours or days from now, you may use the VCR until time for the recording. Just turn off the VCR a few minutes before the recording starts. If you for- get to turn off the VCR, PLEASE TURN OFF VCR FOR TIMER RECORDING flashes on your TV screen two minutes before a timer recording starts. Remove the message by pressing the CLEAR button.

7	POWER		EJECT
7	VCR/TV		SPEED	MEMORY
	REC/OTR			PAUSE/STILL
			PLAY
	REW		F.FWD
			STOP
	MENU	STATUS/EXIT		CLEAR
5	1	2	3
	4	5	6	CH.
	4	5	6
	7	8	9
	MUTE	0	ALT.CH	VOL.
				VOL.
	VCR	TV	CBL/DBS
			VCR PLUS+
	VAR.SLOW		/ENTER	SLOW
	TRACKING		F.ADV	X2 PLAY
	SMART	TIME	INDEX REC END	SKIP
	PICTURE	TIME	INDEX REC END	SKIP

SEARCH

6

Turn off the VCR for the recording.

Insert a tape in the VCR.

Leave the Cable Box/DBS on

(if applicable).

Helpful Hints

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If you are using a Cable Box/DBS, timer recordings are programmed differently. See pages eight and 38-39 for details.

•You may use the VCR Plus+ Programming System to record pro- grams on Cable TV channels up to channel 125.

•If the power fails for more than one minute, some of the programmed VCR PLUS+ channel numbers may be lost. In this case, repeat steps 2- 7 on page 39.

See page 58 for more hints.

Image 41

Contents VRB664AT For Customer Use Dear Philips product ownerDeclaration of Conformity FeaturesIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Recording One Channel/Watching Another Hookups With a Cable Box/Direct Broadcast System cont’dHookups With a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsInstructions continue on Manual Clock SettingDo each step within 60 seconds of the previous step Enter a 0 before a single-digit number Setting the Clock cont’dPress the VCR button, then press the Menu button Automatic Clock SettingTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d RECord/OTR Button REWind/ ButtonMenu Button Number ButtonsStatus Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel VHS Quasi Play Back Sqpb PlayingTurn on the TV and set it to channel 3 or 4, whichever chan RecordingOTR CH12 One-Touch RecordingRecording One Channel/Watching Another Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Checking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System See page 58 for more hints Set the clock. Details are on pages Auto DBS RecordLinkRF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Playing a Tape at Double SpeedDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture Child Lock When Child Lock is activatedSmart Picture Press the VCR button Press the Time Search button Time SearchPress the VCR button Press the Index Search button ExampleSkip Search Record End SearchReal-Time Counter Memory Blue Background Understanding On-Screen Displays Multi-Channel Television Sound SystemMulti-Channel Television Sound System cont’d Please see additional notes on Hi-Fi Stereo Sound SystemHelpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Video Cassette Recorder or Player Limited WarrantyTo obtain a replacement product from Philips Limited Warranty cont’dPayment Amount Payment, if applicableAutomatic IndexPage Page Page Supplied Accessories