Philips VRZ255 owner manual Timer Recording With the VCR Plus+ Programming System

Page 34

34 Timer Recording With the VCR Plus+ Programming System

Follow the steps below to program a timer recording using PlusCode programming numbers. Before you begin make sure:

•Channels are set up. Details are on pages 11 - 12.

•The clock is set. Details are on pages 13 - 17.

•There is a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s).

•The VCR is in VCR position (the VCR light will appear on the display panel). If the VCR light does not appear, press the VCR/TV button once.

•You have programmed the VCR Plus+ and Cable/TV channel numbers. Details are on pages 32 - 33.

Complete each step within 60 seconds of completing the previous step. If you don’t, you may start again at step 1.

1

Press the VCR button.

2

Press the TIMER button.

SELECT , 9 CHOOSE :/OK

AVCR PLUS+

QUICK PROGRAMMING PROGRAM REVIEW

TO END PUSH EXIT

3

Press the PLAY 8 or STOP 9 button to select VCR PLUS+, then press the FF :/OK button.

VCR PLUS+ PROG. CODE

VCR PLUS+ L

TO END PUSH EXIT

4

Use the Number buttons to enter the PlusCode program- ming number of the program you wish to record. (This number is different for every program, and it can be four to eight digits long.)

VCR PLUS+ PROG. CODE

VCR PLUS+ 1234L

TO SET PUSH :/OK

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

		TV			VCR	1
		CBL/DBS	–	+	POWER
		CBL/DBS
		MENU STILL/SLOW			cEJECT	3
		EXIT/STATUS	REW	PLAY	FF /OK
	2	EXIT/STATUS	REW	:	FF /OK
				:
			;;		::
				L
		TIMER [REC/OTR		STOP	S.SEARCH
		TIMER [REC/OTR			S.SEARCH
		1 +	2 +	3
	4	START	STOP	DATE	CH
		4	5	6
		–	–
		DBS	DAILY	WEEKLY
		7	8	9
					VOL
		SPEED	0	CLEAR
		QUICK PROGRAMMING
		VCR/TV	7;;INDEX ::7		AUDIO/MUTE

Helpful Hint

•If you enter an incorrect PlusCode programming number at step 4, ERROR-RE-ENTER CODE will flash on-screen. Enter the correct PlusCode programming number.

Image 34

Contents VRZ255 For Customer Use Dear Philips Magnavox product ownerModel No Serial No Safety Precautions FeaturesIntroduction Table of Contents Before Using Your VCR Hookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d CH3 CH4Connections Hookups With a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel With this connection Cable signal RF coaxial cable TV’sRecording One Channel/Watching Another Cable Box/DBSTurning on Your VCR Press the FF /OK button. The menu shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsManual Clock Setting Instructions continue onWhen the month and day are correct, press the FF /OK button Setting the Clock cont’dPress the EXIT/STATUS button Time Zone Selection Press the FF /OK button repeatedly to select TimeManual PBS Channel Selection Automatic PBS Channel Selection Daylight-Saving Time OFF, PBS CH. and Time Zone will not appear in the menuLanguage Selection Press the EXIT/STATUS buttonRemote Control Buttons EXIT/STATUS Button Timer ButtonMenu Button Speed ButtonDisplay Panel Front Panel Rear Panel Operation If on Screen Mode is set to on or CounterSound program selected Setting the Remote Control to Operate a TV Find the code for your TVSetting the Remote Control to Operate a Cable Box/DBS Find the code for your Cable Box/DBSIf playback does not start automatically, press the Play PlayingRead and follow the steps below to play a tape Button. The 3 light will appear on the VCR display panelPress the VCR button VCR records in a preset volumeRecording Light will appear on the VCR display panelStarting an OTR Channels are set up. Details are on pages 11One-Touch Recording Stopping an OTRRecording One Channel/Watching Another Channels Setting Up the VCR Plus+ Programming SystemStation Setting Up the VCR Plus+ Programming System cont’d 2Examine the lists onTimer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Quick Programming Press the VCR button, then press the Timer buttonComplete each step within 60 seconds of the previous step Tape Speeds Index Checking, Editing, or Clearing Timer Recordings Programmed timer recordings will appearTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoVCR 1 will play your tape. Insert a prerecorded tape in VCR Rerecording Tape DuplicationAudio and video cables are not included Index Search Receiving a Stereo Broadcast Multi-Channel Television Sound SystemReceiving a Second Audio Program Multi-Channel Television Sound System cont’d Hi-Fi Stereo Tape Playback Video Stabilizer Incredible Picture Viewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Renewed Slp Antenna in jack With a stereo TV Ac power cord Hookups Slow motion AccessoriesGlossary Stabilizer Safety precautions Tapes Helpful hints ClearingSupplied Accessories