Philips VRZ255 Hookups Without a Cable Box, Disconnect the antenna or cable from your TV

Page 6

6 Hookups Without a Cable Box

The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please refer to pages 8 - 9. After you hook up the VCR, please go to page 10 to turn on the VCR.

1

Disconnect the antenna or cable from your TV.

Antenna

Indoor/Outdoor

(300 ohm)

75Ω
ANT	/
CABLE

OR

Cable

(75 ohm)

75Ω ANT /

CABLE

ANTENNA IN

Jack

(on back of TV)

2

Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.

Antenna

Indoor/Outdoor

(300 ohm)

OR

Cable

(75 ohm)

			IN	OUT ANT.IN
			R
		AUDIO
			L
		VIDEO		RF OUT
		VIDEO
		CH3	CH4
IN	OUT	ANT.IN
	R
AUDIO
	L
VIDEO		RF OUT
VIDEO
CH3 CH4

Image 6

Contents VRZ255 Dear Philips Magnavox product owner For Customer UseModel No Serial No Features Safety Precautions Introduction Table of Contents Before Using Your VCR Hookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d CH3 CH4Hookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel With this connection Cable signal RF coaxial cable TV’sRecording One Channel/Watching Another Cable Box/DBSTurning on Your VCR Press the FF /OK button. The menu shown below will appearAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsManual Clock Setting Instructions continue onSetting the Clock cont’d When the month and day are correct, press the FF /OK buttonPress the EXIT/STATUS button Time Zone Selection Press the FF /OK button repeatedly to select TimeManual PBS Channel Selection Automatic PBS Channel Selection Daylight-Saving Time OFF, PBS CH. and Time Zone will not appear in the menuLanguage Selection Press the EXIT/STATUS buttonRemote Control Buttons EXIT/STATUS Button Timer ButtonMenu Button Speed ButtonDisplay Panel Front Panel Rear Panel If on Screen Mode is set to on or Counter OperationSound program selected Setting the Remote Control to Operate a TV Find the code for your TVSetting the Remote Control to Operate a Cable Box/DBS Find the code for your Cable Box/DBSIf playback does not start automatically, press the Play PlayingRead and follow the steps below to play a tape Button. The 3 light will appear on the VCR display panelPress the VCR button VCR records in a preset volumeRecording Light will appear on the VCR display panelStarting an OTR Channels are set up. Details are on pages 11One-Touch Recording Stopping an OTRRecording One Channel/Watching Another Setting Up the VCR Plus+ Programming System ChannelsStation Setting Up the VCR Plus+ Programming System cont’d 2Examine the lists onTimer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Press the VCR button, then press the Timer button Quick ProgrammingComplete each step within 60 seconds of the previous step Tape Speeds Index Checking, Editing, or Clearing Timer Recordings Programmed timer recordings will appearTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoRerecording Tape Duplication VCR 1 will play your tape. Insert a prerecorded tape in VCRAudio and video cables are not included Index Search Multi-Channel Television Sound System Receiving a Stereo BroadcastReceiving a Second Audio Program Multi-Channel Television Sound System cont’d Hi-Fi Stereo Tape Playback Video Stabilizer Incredible Picture Viewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DBS Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Renewed Slp Antenna in jack With a stereo TV Ac power cord Hookups Slow motion AccessoriesGlossary Stabilizer Safety precautions Tapes Helpful hints ClearingSupplied Accessories