Philips VRZ222AT owner manual Recording, VCR light does not appear, press the VCR/TV button once

Page 25

VRZ222 layout 4/8/99 10:19 PM Page 25

Read and follow the steps below to record a television program.

1

Turn on the TV and set it to channel 03 or 04, whichever the CH3/CH4 switch on the back of the VCR is set to.

Recording 25

1Turn on the TV.

2Insert a tape in the VCR.

2

Insert a tape with its record tab intact in the VCR.

3

Press the VCR button.

4

If the VCR light appears on the display panel, go to step 5. If the

3

5

POWER

VCR

TV

1 2 3

4 5 6

7 8 9

VCR PLUS+
0	+100
SPEED	MUTE

VCR/TV

CHANNEL

VOLUME

4

6

VCR light does not appear, press the VCR/TV button once.

5

Press the SPEED button until the desired tape speed appears briefly on-screen. (Details about tape speed are on page 30.)

6

Use the CHANNEL o/p buttons or the Number buttons to select the channel to be recorded.

7

Press the REC(ord)/OTR button once to start recording. The REC light will appear.

8

To pause the recording, press the PAUSE/STILL button once. The REC light will flash. To resume recording, press the REC(ord)/OTR button or press the PAUSE/STILL button again. The REC light will come on again.

9

To stop recording, press the STOP/p button.

PLAY

	REW			F.FWD	9
	REW			F.FWD
		STOP
7	REC/OTR	MEMORY		PAUSE/STILL	8
7	MENU	STATUS/EXIT	CLEAR	EJECT	8

Helpful Hints

•If you press the REC(ord)/OTR but- ton when there is not a tape in the VCR, NO CASSETTE will flash on- screen.

•If you press the REC(ord)/OTR but- ton while a tape without a record tab is in the VCR, the VCR will eject the tape and PROTECTED CAS- SETTE CANNOT RECORD will flash on-screen.

•Other recording options are on pages 26 - 36.

•You can change the tape speed during a recording, but some distor- tion will appear on the tape.

•The VCR will record in a preset vol-

ume.

Image 25

Contents VRZ222AT For Customer Use Dear Philips Magnavox product ownerSafety Precautions FeaturesIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemANT Audio OUT Plug in the TV and the VCRConnections Hookups With a Cable Box / Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box / Direct Broadcast System cont’dHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single digit num- ber Setting the ClockDaylight-Saving Time Language Selection Speed Button Remote Control ButtonsRemote Control Buttons cont’d Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing VCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingInstructions continue on Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMSee page 42 for more hints Checking or Cancelling Timer RecordingsChannels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Press the VCR PLUS+ button Do each step within 60 seconds of the previous stepTimer Recording With the VCR Plus+ Programming System cont’d Antenna Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayReal-Time Counter Memory Super High Speed Searching LP/SLP Forward and Reverse Searching SP/LP/SLPViewing a Still Picture Automatic Operation Features Specifications Helpful Hints Helpful Hints cont’d Cable Box Output Channel 03 or GlossaryVideo Cassette Recorder Limited WarrantyAutomatic IndexVRZ222 layout 4/8/99 1019 PM Supplied Accessories