Philips VRZ222AT owner manual Hookups With a Cable Box / Direct Broadcast System cont’d

Page 9

VRZ222 layout 4/8/99 10:19 PM Page 9

Hookups With a Cable Box / Direct Broadcast System (cont’d) 9

With this connection:

●You may watch one channel while recording another.

●You may not record scrambled channels.

1 VCR

ANT

IN

2 Cable Box/DBS

OUT

IN

OUT

VIDEO CH3 CH4

Cable signal

IN

OUT

RF coaxial

cable

75V
ANT	/
CABLE

RF coaxial

cable

3 TV’s ANTENNA

IN Jack

Connections

1

Connect a Cable signal to the VCR’s ANT(enna) IN Jack.

2

Use an RF coaxial cable (supplied) to connect the OUT Jack on the VCR to the IN Jack on the Cable Box/DBS.

3

Use a second RF coaxial cable to connect the OUT Jack on the Cable Box/DBS to the ANTENNA IN Jack on the TV.

Recording One Channel/Watching Another

1

Put the Cable Box/DBS on the same channel as the VCR’s CH3/CH4 switch. Then, with the VCR in VCR position (the VCR light will appear on the display panel), use the CHANNEL o/p buttons to select the channel you want to record at the VCR. Start the recording.

2

Press the VCR/TV button once to put the VCR in TV position. (The VCR light will disappear.)

3

Set the TV to the Cable Box/DBS output channel (03 or 04).

4

Select the channel you want to watch at the Cable Box/DBS.

Helpful Hint

•When you play a tape, make sure the Cable Box/DBS is set to the same channel as the CH3/CH4 switch on the VCR. Set the TV to the Cable Box/DBS output channel (03 or 04).

Image 9

Contents VRZ222AT For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemANT Audio OUT Plug in the TV and the VCRHookups With a Cable Box / Direct Broadcast System ConnectionsRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box / Direct Broadcast System cont’dHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single digit num- ber Setting the ClockDaylight-Saving Time Language Selection Speed Button Remote Control ButtonsRemote Control Buttons cont’d Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Playing VCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another One-Touch Recording Daily Timer RecordingInstructions continue on Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMSee page 42 for more hints Checking or Cancelling Timer RecordingsChannels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Press the VCR PLUS+ button Do each step within 60 seconds of the previous stepTimer Recording With the VCR Plus+ Programming System cont’d Antenna Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayReal-Time Counter Memory Forward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPViewing a Still Picture Automatic Operation Features Specifications Helpful Hints Helpful Hints cont’d Cable Box Output Channel 03 or GlossaryVideo Cassette Recorder Limited WarrantyAutomatic IndexVRZ222 layout 4/8/99 1019 PM Supplied Accessories