Philips VR400BMG Picture Select, Press the Play button or the Stop button repeatedly to

Page 36

36 Picture Select

This function enables you to select the picture quality of a tape.

Make sure:

●The VCR is on and is in VCR position. The VCR/TV light will appear. If it does not, press the VCR/TV button once.

●There is a tape in the VCR.

1

During tape playback, press the MENU button until the main menu appears.

- M E N U -

 

POWER

 

VCR/TV EJECT

TIMER PROGRAMMING

1

2

3

AUTO REPEAT

[OFF]

BPICTURE SELECT

CHANNEL SET UP

4

5

6

 

CLOCK SET

 

 

 

 

 

LANGUAGE SELECT

 

 

 

 

AUTO SATELLITE LINK

7

8

9

CHANNEL

 

 

2

SPEED

0

+100

 

SLOW

QUICK-

SEARCH

TIME INDEX

FIND

Press the PLAY button or the STOP button repeatedly to

1

MENU

 

 

 

3

select PICTURE SELECT. Then, press the F.FWD button.

DISPLAY

EXIT

COUNTER

 

 

 

 

3

 

 

RESET MEMORY

REWIND

/ PLAY

F.FWD

 

RECORD

 

/ STOP

PAUSE/STILL

With in five seconds, press the F.FWD button until your

 

 

 

 

 

2

desired mode (NORMAL, SOFT or SHARP) appears on

 

 

 

 

 

the screen.

 

 

 

 

 

Helpful Hint

•You may only set the Picture Select during tape playback.

Page 35 Page 37
Image 36
Page 35 Page 37
Contents VCR Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Before Using Your VCR Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the AC power cords of the TV and the VCR CH3 CH4Cable Signal ConnectionsRecording/Viewing Any Channel Signal Recording One Channel/Watching AnotherCable Box/DBS CableHookups With a Stereo TV Turning on Your VCR Below will appearAutomatic Channel Setup Press the Menu button until the main menu appearsAutomatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d Your selection will flash on the screen in the AM/PM spacePress the Counter RESET/EXIT button to exit Language SelectionOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Status Displays Remote Control Buttons Counter RESET/EXIT Button Eject ButtonTime Search Button Index Search ButtonVCR Display Panel Speed Button Power Button Remote Sensor FWD Fast Forward ButtonVCR/TV Button Play ButtonAC Power Cord Rear PanelVideo OUT Jack Video in JackPlaying VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording 1Turn on the TV Insert a tapeOne-Touch Recording Starting an OTRStopping an OTR Timer Recording Channels are set up Clock is setTimer Recording cont’d Repeat the procedure in to set the recording’s end timeEnter the recording’s start time Start Time END Time Channel REC Speed SLP Timer Recording cont’d Cancelling a Timer RecordingCorrecting a Timer Recording 42&5Auto Satellite Link Using a Satellite Tuner Set the program to be recorded On the satellite tunerPress the VCR/TV button on the VCR remote control to Recording One Channel/Watching AnotherTo return to the channel being recorded, use the TV Put the VCR in VCR position. The VCR/TV light will appearRerecording Tape Duplication AntennaRepeat Play Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PicturePicture Select Press the Play button or the Stop button repeatedly toSelect Picture SELECT. Then, press the F.FWD button Real-Time Counter Memory Press the Play button to watch the tapeIndex Search Press the Index Search buttonTime Search Press the Time Search buttonQuick Find Press the QUICK-FIND buttonTo resume normal tape playback, press the Play button Automatic Playback Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories
Top Page Image Contents