Philips VR400BMG owner manual 42&5, Correcting a Timer Recording

Page 30

30 Timer Recording (cont’d)

Correcting a Timer Recording

If you need to correct a timer recording after you have finished setting the program, follow these steps. Make sure the VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.)

1

Press the MENU button.The details of your program appear on the screen.

	TIMER PROGRAMMING
	DATE	STA/END	CH
B1 05/04		07:30 PM	16
	THU	08:30 PM	SP
3	05/11	10:00 PM	125
	W THU	10:54 PM	SLP
5	05/21	11:00 PM	40
	DAILY	11:30 PM	SLP

2

Press the PLAY button or the STOP button to select the timer recording you want to correct.

NOTE: If some empty program numbers exist, the lower program num- ber appears on the screen by pressing the REWIND button. In this case, you can enter the new program.

3

Press the F.FWD button.

ONE TIME PROGRAM

PROGRAM NUMBER			1
PROGRAM NUMBER			1
DATE	05/04		THU
START TIME 07:30			PM
END TIME 08:30			PM
CHANNEL	16
REC SPEED	SP

1

4

POWER

VCR/TV

EJECT

1 2 3

4 5 6

7 8 9 CHANNEL

	SPEED	0	+100
	SLOW	QUICK-	SEARCH
		QUICK-	TIME	INDEX
		FIND	TIME	INDEX
	MENU	DISPLAY	EXIT	COUNTER
			RESET	MEMORY
	REWIND	/ PLAY		F.FWD
	RECORD		/ STOP	PAUSE/STILL

6

3

42&5

Select the information you want to change using the F.FWD button. Press the REWIND button to go back one step. (There is an exception. Do not press the REWIND button while the program number is flashing. If you do, you will cancel the timer recording completely.)

5

While the information is flashing, enter the correct infor- mation by pressing the PLAY button or the STOP button.

6

When all the information is correct, press the COUNTER RESET/EXIT button to exit. Turn off the VCR before the timer recording.

Image 30

Contents VCR Warranty Verification For Customer UseIntroduction FeaturesSafety Precautions Declaration of ConformityTable of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR maintenanceHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the AC power cords of the TV and the VCR CH3 CH4Cable Signal ConnectionsRecording/Viewing Any Channel Cable Box/DBS SignalRecording One Channel/Watching Another CableHookups With a Stereo TV Turning on Your VCR Below will appearAutomatic Channel Setup Press the Menu button until the main menu appearsAutomatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d Your selection will flash on the screen in the AM/PM spacePress the Counter RESET/EXIT button to exit Language SelectionOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Status Displays Remote Control Buttons Time Search Button Counter RESET/EXIT ButtonEject Button Index Search ButtonVCR Display Panel VCR/TV Button Speed Button Power ButtonRemote Sensor FWD Fast Forward Button Play ButtonVideo OUT Jack AC Power CordRear Panel Video in JackPlaying VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording 1Turn on the TV Insert a tapeOne-Touch Recording Starting an OTRStopping an OTR Timer Recording Channels are set up Clock is setTimer Recording cont’d Repeat the procedure in to set the recording’s end timeEnter the recording’s start time Start Time END Time Channel REC Speed SLP Timer Recording cont’d Cancelling a Timer RecordingCorrecting a Timer Recording 42&5Auto Satellite Link Using a Satellite Tuner Set the program to be recorded On the satellite tunerTo return to the channel being recorded, use the TV Press the VCR/TV button on the VCR remote control toRecording One Channel/Watching Another Put the VCR in VCR position. The VCR/TV light will appearRerecording Tape Duplication AntennaRepeat Play Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PicturePicture Select Press the Play button or the Stop button repeatedly toSelect Picture SELECT. Then, press the F.FWD button Real-Time Counter Memory Press the Play button to watch the tapeIndex Search Press the Index Search buttonTime Search Press the Time Search buttonQuick Find Press the QUICK-FIND buttonTo resume normal tape playback, press the Play button Automatic Playback Features Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel Channel 3 orSpecifications Renewed Index Supplied Accessories