Philips VR400BMG owner manual Helpful Hints cont’d

Page 43

Helpful Hints (cont’d) 43

Tape cannot be removed.

•Make sure the power plug is completely connected to an AC (alternating current) outlet.

•You have set a timer recording. Turn on the VCR power, then eject the tape. Be sure to insert a tape and turn off the VCR for your timer recording.

Tape cannot be inserted.

•Insert the tape, window side up, with the record tab facing you.

•Make sure a tape isn’t already in the VCR by pressing the STOP/EJECT button on the VCR or the EJECT button on the remote control.

•Gently push on the center of the tape when putting it in the VCR. Never force the tape into the VCR.

•If a timer recording is set, the VCR will not accept a tape that does not have a record tab. You may only insert a tape with the record tab intact.

VCR ejects the tape when the RECORD button is pressed or when the VCR power is turned off to set a timer recording.

• Make sure the tape has a record tab. Details are on page five.

There is no playback picture, or the playback picture is noisy or contains streaks.

•Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch. Details are on page seven.

•Make sure the VCR is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.)

•Make sure channel 3 or 4 is properly adjusted.

•Adjust the tracking. Details are on page 41.

•TVs placed too close to the VCR can cause interference during tape playback. Move the VCR away from the TV.

TV programs cannot be watched normally.

•Press the VCR/TV button to put the VCR in TV position. (The VCR/TV light will disappear.)

•Check the connections between the VCR, TV, antenna/cable, and Cable Box/DBS (if applicable). Details are on pages six-10.

The reception on all channels is poor.

• You may need to tune your TV again.

Line Input

•If you accidentally enter Line Input mode (LineIn Rear (L1) will appear on your TV screen briefly), press the CHANNEL (o/p) buttons or use the Number buttons to select another channel.

The playback picture is too dim, too bright, or fluctuates in brightness.

•Some programs may be broadcast with copyright protection technology in order to protect the rights of copyright owners. This technology is used on programs that are recorded on video tapes or Digital Video Discs (DVDs), as well as some programs broadcast by antenna/cable/satellite television channels. Programs broadcast with copyright protection technology may not record clearly. Likewise, if you play a tape that is a recording of a copyright protected program, the picture may not be clear. Tapes of copy- right protected programs may have a picture that is dark or dim, or the brightness of the picture may fluctuate. Therefore, you should avoid recording or playing copies of copyright protected programs. This VCR incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights own- ers. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Page 42 Page 44
Image 43
Page 42 Page 44
Contents VCR For Customer Use Warranty VerificationDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents VCR maintenance Before Using Your VCRPutting Batteries in the Remote Control Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemCH3 CH4 Plug in the AC power cords of the TV and the VCRConnections Cable SignalRecording/Viewing Any Channel Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Below will appear Turning on Your VCRPress the Menu button until the main menu appears Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dFollow the steps below to set your VCR’s clock. Make sure Setting the ClockYour selection will flash on the screen in the AM/PM space Setting the Clock cont’dLanguage Selection Press the Counter RESET/EXIT button to exitPress the Display button once Clock mode OFF mode Press the Display button once Count modeOn-Screen Status Displays Remote Control Buttons Index Search Button Counter RESET/EXIT ButtonEject Button Time Search ButtonVCR Display Panel Play Button Speed Button Power ButtonRemote Sensor FWD Fast Forward Button VCR/TV ButtonVideo in Jack AC Power CordRear Panel Video OUT JackVHS Quasi Play Back Sqpb PlayingRead and follow the steps below to play a tape 1Turn on the TV Insert a tape RecordingStarting an OTR One-Touch RecordingStopping an OTR Channels are set up Clock is set Timer RecordingRepeat the procedure in to set the recording’s end time Timer Recording cont’dEnter the recording’s start time Start Time END Time Channel REC Speed SLP Cancelling a Timer Recording Timer Recording cont’d42&5 Correcting a Timer RecordingSet the program to be recorded On the satellite tuner Auto Satellite Link Using a Satellite TunerPut the VCR in VCR position. The VCR/TV light will appear Press the VCR/TV button on the VCR remote control toRecording One Channel/Watching Another To return to the channel being recorded, use the TVAntenna Rerecording Tape DuplicationRepeat Play Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPPress the Play button or the Stop button repeatedly to Picture SelectSelect Picture SELECT. Then, press the F.FWD button Press the Play button to watch the tape Real-Time Counter MemoryPress the Index Search button Index SearchPress the Time Search button Time SearchPress the QUICK-FIND button Quick FindTo resume normal tape playback, press the Play button Automatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or GlossarySpecifications Renewed Index Supplied Accessories
Top Page Image Contents