Philips VR400BMG owner manual CH3 CH4, Plug in the AC power cords of the TV and the VCR

Page 7

Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

ANT

IN

					AUDIO
				ANT	OUT IN	OUT
				ANT	VIDEO	CH3 CH4
					VIDEO
				IN			75
							75
							ANT /
AUDIO							CABLE
AUDIO
OUT	IN			OUT			ANTENNA IN Jack
							ANTENNA IN Jack
VIDEO		CH3	CH4				(on back of TV)
VIDEO						RF coaxial cable	example only
							example only

4

Plug in the AC power cords of the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

ANT

IN

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

AUDIO
OUT	IN	OUT
VIDEO		CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Contents VCR For Customer Use Warranty VerificationDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents VCR maintenance Before Using Your VCRPutting Batteries in the Remote Control Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemCH3 CH4 Plug in the AC power cords of the TV and the VCRConnections Cable SignalRecording/Viewing Any Channel Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Below will appear Turning on Your VCRPress the Menu button until the main menu appears Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dFollow the steps below to set your VCR’s clock. Make sure Setting the ClockYour selection will flash on the screen in the AM/PM space Setting the Clock cont’dLanguage Selection Press the Counter RESET/EXIT button to exitPress the Display button once Clock mode OFF mode Press the Display button once Count modeOn-Screen Status Displays Remote Control Buttons Index Search Button Counter RESET/EXIT ButtonEject Button Time Search ButtonVCR Display Panel Play Button Speed Button Power ButtonRemote Sensor FWD Fast Forward Button VCR/TV ButtonVideo in Jack AC Power CordRear Panel Video OUT JackVHS Quasi Play Back Sqpb PlayingRead and follow the steps below to play a tape 1Turn on the TV Insert a tape RecordingStarting an OTR One-Touch RecordingStopping an OTR Channels are set up Clock is set Timer RecordingRepeat the procedure in to set the recording’s end time Timer Recording cont’dEnter the recording’s start time Start Time END Time Channel REC Speed SLP Cancelling a Timer Recording Timer Recording cont’d42&5 Correcting a Timer RecordingSet the program to be recorded On the satellite tuner Auto Satellite Link Using a Satellite TunerPut the VCR in VCR position. The VCR/TV light will appear Press the VCR/TV button on the VCR remote control toRecording One Channel/Watching Another To return to the channel being recorded, use the TVAntenna Rerecording Tape DuplicationRepeat Play Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPPress the Play button or the Stop button repeatedly to Picture SelectSelect Picture SELECT. Then, press the F.FWD button Press the Play button to watch the tape Real-Time Counter MemoryPress the Index Search button Index SearchPress the Time Search button Time SearchPress the QUICK-FIND button Quick FindTo resume normal tape playback, press the Play button Automatic Playback Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel Channel 3 or GlossarySpecifications Renewed Index Supplied Accessories