Philips VRA471AT owner manual Hookups With a Stereo TV

Page 10

10 Hookups With a Stereo TV

		antenna or
		1 ANT(enna)cable to
	ANT	IN Jack
	IN	IN Jack
AUDIO
OUT IN	OUT
VIDEO	CH3 CH4
VIDEO	2
VIDEO (yellow) and	2
VIDEO (yellow) and
AUDIO (white) OUT Jacks		Video Cable
		Video Cable
3		Audio Cable

Audio and Video IN Jacks on TV

●Audio and Video cables are not supplied.

1

Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.

2

Connect a video cable to the yellow VIDEO OUT Jack on the back of the VCR. Then, connect the other end of the video cable to the VIDEO IN Jack on your TV.

3

Connect an audio cable to the white AUDIO OUT Jack on the back of the VCR. Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV.

(If your TV has Right and Left AUDIO IN Jacks, you must use a “Y” splitter audio cable as illustrated to deliver audio to the TV’s right and left channels.)

4

Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owner’s manual for details.

Helpful Hint

• This hookup will not give you stereo sound. To get stereo sound, use the connections on pages six-seven and select the channel to be viewed at the TV (with the VCR turned off).

Image 10

Contents VRA471AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoFeatures IntroductionTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System Recording/Viewing Any ChannelRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Automatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Do each step within 60 seconds of the previous stepSetting the Clock cont’d Automatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV 2TV codeCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Menu Button REWind/ ButtonRECord/OTR Button Number ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Press the Eject button to remove the tapeTurn on the TV and set it to channel 3 or 4, whichever RecordingIf the VCR light appears on the display panel, go to . If One-Touch Recording OTR CH12Recording One Channel/Watching Another Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings See page 56 for more hintsChannels Setting Up the VCR Plus+ Programming SystemCall Letters Setting Up the VCR Plus+ Programming System cont’d Examine the lists onTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Auto DBS RecordLink Set the program to Be recorded on the satellite tunerRerecording Tape Duplication RF coaxial cablePress the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture Still picture will appear on the screenTV and Cable Box/DBS feature buttons of the remote When Child Lock is activatedDuring the timer recording Child LockLetting your VCR find your remote for you If another remote control beepsPress the Mute button, then press the PAUSE/STILL button Time Search Press the VCR button Press the Time Search buttonExample Press the VCR button Press the Index Search buttonRecord End Search Skip SearchQuick Search To resume normal tape playback, press the PLAY/o buttonReal-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Timer PowerRemote control AutomaticPage Page Supplied Accessories