Philips VRA471AT owner manual Glossary, Cable Box/DBS Output Channel 03 or

Page 58

58 Glossary

AUDIO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record audio from another source (IN) or to send audio to another system (OUT).

Automatic Channel Setup: process in which the VCR memo- rizes all available channels. Then, when you press the CH(annel) o/p button, you only scan through channels you receive.

Bands: settings that allow you to tune channels.

Antenna – VHF (very high frequency; channels 2-13) and UHF (ultra high frequency; channels 14-69).

Cable – all standard channels can be received without a Cable Box/DBS.

Cable Box/DBS Output Channel: 03 or 04.

Dubbing: copying a tape using a second VCR.

Frame: a still picture.

HQ: high quality; a feature in the VCR circuitry which provides enhanced picture detail.

Line Input: The channel to which you set your VCR during dub- bing. If you use the AUDIO and VIDEO In jacks on the front of the VCR, select channel 002 (AV FRONT). If you use the AUDIO and VIDEO IN jacks on the back of the VCR, select 001 (AV REAR).

If you accidentally enter Line Input mode, press the CH(annel) o/p button or use the Number buttons to select another chan- nel.

OTR: One-Touch Recording; a timed recording that starts imme- diately and records for 30 minutes to eight hours.

Remote Control: the small electronic unit that came with your VCR; allows you to operate your VCR from a distance. You may be able to operate your TV, Cable Box, or Direct Broadcast System with the remote control.

RF coaxial cable: The cable supplied with your VCR. Use it to connect your VCR to your TV (or Cable Box or DBS). The sup- plied cable is a snap-on type. However, you may use a screw-on type if you prefer.

Special Effects: forward and reverse searching; a still picture; slow motion playback.

Tape Speeds: how fast the tape travels during a recording or playback.

SP (standard play) – fastest tape speed (recording time for a T120 tape is approximately two hours); best picture quality.

LP (long play) – average tape speed; playback only.

SLP (super long play) – slowest tape speed (recording time for a T120 tape is approximately six hours).

VCR: video cassette recorder.

VIDEO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record video from another source (IN) or to send video to another system (OUT).

Image 58
Contents VRA471AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoFeatures IntroductionTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System Recording/Viewing Any ChannelRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Automatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Do each step within 60 seconds of the previous stepSetting the Clock cont’d Automatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV 2TV codeCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Menu Button REWind/ ButtonRECord/OTR Button Number ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Press the Eject button to remove the tapeTurn on the TV and set it to channel 3 or 4, whichever RecordingIf the VCR light appears on the display panel, go to . If One-Touch Recording OTR CH12Recording One Channel/Watching Another Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings See page 56 for more hintsChannels Setting Up the VCR Plus+ Programming SystemCall Letters Setting Up the VCR Plus+ Programming System cont’d Examine the lists onTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Auto DBS RecordLink Set the program to Be recorded on the satellite tunerRerecording Tape Duplication RF coaxial cablePress the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture Still picture will appear on the screenTV and Cable Box/DBS feature buttons of the remote When Child Lock is activatedDuring the timer recording Child LockLetting your VCR find your remote for you If another remote control beepsPress the Mute button, then press the PAUSE/STILL button Time Search Press the VCR button Press the Time Search buttonExample Press the VCR button Press the Index Search buttonRecord End Search Skip SearchQuick Search To resume normal tape playback, press the PLAY/o buttonReal-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Timer PowerRemote control AutomaticPage Page Supplied Accessories