Philips VRA471AT On-Screen Status Displays, Status Display example only, If you select Status OFF

Page 26

26 On-Screen Status Displays

A status display will appear when you press the STATUS/EXIT but- ton or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below.

If you select STATUS ON, then select COUNTER ONLY ON:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. After five seconds, only the counter will remain on the screen. You must press the STATUS/EXIT button to remove it. Portions of the status display also may appear when you press other function buttons.

If you select STATUS ON, then select COUNTER ONLY OFF:

●Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the sta- tus display also may appear when you press other function but- tons.

If you select STATUS OFF:

●The status display will not appear when you press function but- tons. You must press the STATUS/EXIT button to see the status display.

1

Press the VCR button, then press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

3

Press the PLAY/o button or the STOP/p button to select ON SCREEN MODE, then press the F.FWD/B button.

4

Press the PLAY/o button or the STOP/p button to select STATUS, then press the F.FWD/B button so that OFF (or ON) appears beside STATUS.

SELECT op CHOOSE B

→ STATUS	[ON]
COUNTER ONLY	[OFF]

TO END PUSH EXIT

5

If you set STATUS to OFF, go to step 6. If you set STA- TUS to ON, press the PLAY/o button or the STOP/p button to select COUNTER ONLY, then press the F.FWD/B button so that OFF (or ON) appears beside it.

6

Press the STATUS/EXIT button.

Status Display (example only)

Current status

of tape		Time


STOP		12:00 AM
		CH10
SLP		M 1:23:45

Channel

Tape Counter

Speed and

Counter

Memory

Helpful Hint

•You may not access a status display when viewing a still picture, during slow motion playback, or during for- ward or reverse searching.

Image 26

Contents VRA471AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoFeatures IntroductionTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System Recording/Viewing Any ChannelRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Automatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Do each step within 60 seconds of the previous stepSetting the Clock cont’d Automatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV 2TV codeCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Menu Button REWind/ ButtonRECord/OTR Button Number ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Press the Eject button to remove the tapeIf the VCR light appears on the display panel, go to . If RecordingTurn on the TV and set it to channel 3 or 4, whichever One-Touch Recording OTR CH12Recording One Channel/Watching Another Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings See page 56 for more hintsCall Letters Setting Up the VCR Plus+ Programming SystemChannels Setting Up the VCR Plus+ Programming System cont’d Examine the lists onTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Auto DBS RecordLink Set the program to Be recorded on the satellite tunerRerecording Tape Duplication RF coaxial cablePress the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Automatic Operation Features Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture Still picture will appear on the screenTV and Cable Box/DBS feature buttons of the remote When Child Lock is activatedDuring the timer recording Child LockPress the Mute button, then press the PAUSE/STILL button If another remote control beepsLetting your VCR find your remote for you Time Search Press the VCR button Press the Time Search buttonExample Press the VCR button Press the Index Search buttonRecord End Search Skip SearchQuick Search To resume normal tape playback, press the PLAY/o buttonWhile the status display is on the screen, press Clear button to reset the real-time counter to zeroReal-Time Counter Memory Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Timer PowerRemote control AutomaticPage Page Supplied Accessories