Philips VRA471AT REWind/ Button, RECord/OTR Button, Menu Button, Number Buttons, Cable Users

Page 25

Remote Control Buttons (cont’d) 25

POWER

 

 

EJECT

VCR/TV

 

SPEED

MEMORY

REC/OTR

 

 

PAUSE/STILL

 

 

PLAY

 

REW

 

 

F.FWD

 

 

STOP

 

MENU

STATUS/EXIT

CLEAR

1

2

3

 

4

5

6

CH.

 

7

8

9

 

MUTE

0

ALT.CH

VOL.

 

 

 

VCR

TV

CBL/DBS

 

 

 

VCR PLUS+

 

VAR.SLOW

 

/ENTER

SLOW

TRACKING

 

F.ADV

X2 PLAY

QUICK TIME INDEX REC END SKIP

SEARCH

REW(ind)/{ Button

When tape playback is stopped, press to rewind the tape at high speed. During playback, press to rewind the tape while the picture stays on the screen. Details are on page 46. Press to return to a previous on-screen menu. Or, if you have a Magnavox, Philips, or Philips Magnavox TV, use the REW(ind)/{ button to adjust the controls in the TV menu.

REC(ord)/OTR Button

Press once to start a recording. Details are on page 31. Or, press repeated- ly to start a One-Touch Recording. Details are on page 32.

MENU Button

Press to access the VCR menu. Or, if you have a Magnavox, Philips, or Philips Magnavox TV, press the TV button, then press the MENU button to display the TV menu.

Number Buttons

Press to select channels at the VCR, TV, Cable Box, or Direct Broadcast System; use to set up VCR features (such as the clock). (You can not select channels above 99 at the Magnavox, Philips, or Philips Magnavox TV.)

Cable Users

Enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. (There also may be a brief delay when you select channels 10, 11, and 12.) If you want to select channels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7.

Antenna Users

Enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay. You may only select channels 2-69.

ALT. CH (Alternate Channel) Button

Press while in TV mode to return to the TV channel you were viewing immediately before switching to your current channel. This button does not have an effect on channels changed at the VCR.

TRACKING o/p Button

During normal or slow motion playback, press to adjust the tracking. Details are on page 45.

VAR(iable). SLOW Button

During slow motion playback, press to vary the tape playback speed from 1/6 to 1/30 of normal speed. Details are on page 47.

MUTE Button

Press to eliminate the TV’s sound. Press again to restore the volume.

Helpful Hints

Press the VCR button before pressing other VCR buttons; press the TV button before pressing other TV buttons; press the CBL/DBS button before pressing other Cable Box/Direct Broadcast System buttons.

The buttons with a shaded description may also operate features of your TV, Cable Box, or Direct Broadcast System.

Buttons that are shaded in the illustration light up for five seconds when you press any button on the remote control.

Image 25
Contents VRA471AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoIntroduction FeaturesTable of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dHookups With a Cable Box/Direct Broadcast System Cable Signal RF coaxialConnections Recording/Viewing Any ChannelConnect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsDo each step within 60 seconds of the previous step Manual Clock SettingSetting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock SettingTime Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TVCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d RECord/OTR Button REWind/ ButtonMenu Button Number ButtonsStatus Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Press the Eject button to remove the tapeTurn on the TV and set it to channel 3 or 4, whichever RecordingIf the VCR light appears on the display panel, go to . If OTR CH12 One-Touch RecordingRecording One Channel/Watching Another Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dSee page 56 for more hints Checking or Cancelling Timer RecordingsChannels Setting Up the VCR Plus+ Programming SystemCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’dTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLinkRF coaxial cable Rerecording Tape DuplicationPress the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Playing a Tape at Double SpeedViewing a Slow Motion Picture Viewing a Still PictureDuring tape playback, press the PAUSE/STILL button. a Still picture will appear on the screenDuring the timer recording When Child Lock is activatedTV and Cable Box/DBS feature buttons of the remote Child LockLetting your VCR find your remote for you If another remote control beepsPress the Mute button, then press the PAUSE/STILL button Press the VCR button Press the Time Search button Time SearchPress the VCR button Press the Index Search button ExampleSkip Search Record End SearchTo resume normal tape playback, press the PLAY/o button Quick SearchReal-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyRemote control PowerTimer AutomaticPage Page Supplied Accessories