Philips VRA471AT Setting Up the VCR Plus+ Programming System cont’d, Examine the lists on

Page 39

Setting Up the VCR Plus+ Programming System (cont’d) 39

2

Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. For stations whose VCR Plus+ and Cable/TV channels do not match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers by following steps 3-7. Make each entry within 60 seconds of the previous entry.

3

Press the VCR button, then press the MENU button.

2 Examine the lists on page 38.

4-6

POWER

 

EJECT

VCR/TV

SPEED

MEMORY

REC/OTR

 

PAUSE/STILL

4

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B

 

→REPEAT PLAY

OFF

ON SCREEN MODE

 

LANGUAGE

 

VCR PLUS+ REF. MAP

 

BLUE BACKGROUND

ON

AUTO DBS

OFF

RECORD LINK

 

TO END PUSH EXIT

 

5

7 REW

3

MENU

1

4

7

MUTE

VCR

PLAY

F.FWD

STOP

STATUS/EXIT

CLEAR

 

 

2 3

CH.

5 6

8 9 6

0ALT.CH

VOL.

TV CBL/DBS

Press the PLAY/o button or the STOP/p button to select VCR PLUS+ REF. MAP, then press the F.FWD/B button.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1 – – – – –> 1

22

TO SELECT CH PUSH op

THEN ENTER CH NO. TO END PUSH EXIT

 

VCR PLUS+

 

VAR.SLOW

/ENTER

SLOW

TRACKING

F.ADV

X2 PLAY

QUICK TIME

INDEX REC END

SKIP

 

SEARCH

 

6

Look at the lists you filled in on page 38. For stations whose VCR

Plus+ and Cable/TV channels do not match, press the PLAY/o button or the STOP/p button until the arrow is beside the VCR Plus+ channel you need. Then, press the Number buttons to enter the corresponding Cable/TV channel from your list. Enter all the stations on your list.

●If you are recording from line input, press 0,0 to select AUX.

●If you are using a Cable Box/DBS, the Cable/TV channel will be 3 or 4 (the Cable Box/DBS output channel) for every VCR Plus+ channel. You must set the Cable Box/DBS to the channel you want to record; leave the Cable Box/DBS on for the timer recording.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1– – – – –> 23

22

TO SELECT CH PUSH op

THEN ENTER CH NO.

TO END PUSH EXIT

7

Press the STATUS/EXIT button.

Helpful Hints

•To erase a Cable/TV channel num- ber, repeat steps 3-5 on this page. Then, press the PLAY/o button or the STOP/p button until the arrow appears beside the Cable/TV chan- nel you need to erase. Press the CLEAR button, then press the STA- TUS/EXIT button.

•When you receive the VCR, all the VCR Plus+ channel numbers and Cable/TV channel numbers are the

same.

•If you are recording from line input, connect the audio and video cables to the AUDIO IN and VIDEO IN jacks on the back of the VCR. (Please see illustration on page 43.)

Page 38 Page 40
Image 39
Page 38 Page 40
Contents VRA471AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialIntroduction FeaturesTable of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dRecording/Viewing Any Channel Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System ConnectionsCable Box/DBS Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Recording One Channel/Watching AnotherHookups With a Stereo TV Turning on Your VCR 2Turn on the TVPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsDo each step within 60 seconds of the previous step Manual Clock SettingSetting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock SettingTime Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TVCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Number Buttons REWind/ ButtonRECord/OTR Button Menu ButtonIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Press the Eject button to remove the tape PlayingRead and follow the steps below to play a tape 1Turn on the TV 2Insert a tape in the VCRRecording Turn on the TV and set it to channel 3 or 4, whicheverIf the VCR light appears on the display panel, go to . If OTR CH12 One-Touch RecordingRecording One Channel/Watching Another Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dSee page 56 for more hints Checking or Cancelling Timer RecordingsSetting Up the VCR Plus+ Programming System ChannelsCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’dTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLinkRF coaxial cable Rerecording Tape DuplicationRepeat Play Press the PLAY/o button or the STOP/p button to selectPress the F.FWD/B button so that on appears beside Automatic Operation Features Playing a Tape at Double Speed Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPStill picture will appear on the screen Viewing a Still PictureViewing a Slow Motion Picture During tape playback, press the PAUSE/STILL button. aChild Lock When Child Lock is activatedDuring the timer recording TV and Cable Box/DBS feature buttons of the remoteIf another remote control beeps Letting your VCR find your remote for youPress the Mute button, then press the PAUSE/STILL button Press the VCR button Press the Time Search button Time SearchPress the VCR button Press the Index Search button ExampleSkip Search Record End SearchTo resume normal tape playback, press the PLAY/o button Quick SearchClear button to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyAutomatic PowerRemote control TimerPage Page Supplied Accessories
Top Page Image Contents