Philips VRA471AT Real-Time Counter Memory, While the status display is on the screen, press

Page 54

54 Real-Time Counter Memory

Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later.

1,5

1

Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP/p button to stop the tape.

2

Press the STATUS/EXIT button to see the status display.

POWER

VCR/TVSPEED

REC/OTR

PLAY

REW

STOP

EJECT

MEMORY4

PAUSE/STILL

F.FWD

STOP	1:08PM
	CH10

SLP 1 : 23 : 45

3

While the status display is on the screen, press the

MENU

2 1

4

7

MUTE

STATUS/EXIT

2 3

5 6

89

0ALT.CH

CLEAR

3

CH.

VOL.

CLEAR button to reset the real-time counter to zero.

STOP	1:08 PM
	CH10

SLP 0 : 00 : 00

4

While the real-time counter is on the screen, press the MEMORY button so that M appears beside the counter.

STOP	1:08 PM
	CH10

SLP M 0 : 00 : 00

5

To go to a tape location where the real-time counter was reset to zero, press the REW(ind)/{ button or the F.FWD/B button when playback is stopped.

When the tape reaches the point at which the counter was set to zero, the tape will stop.

Press the PLAY/o button to watch the tape.

VCR	TV	CBL/DBS
		VCR PLUS+
VAR.SLOW		/ENTER	SLOW
TRACKING		F.ADV	X2 PLAY
QUICK	TIME	INDEX REC END	SKIP
		SEARCH

Helpful Hints

•The MEMORY button does not function if REPEAT PLAY is set to ON. Details are on page 44.

•To erase a real-time counter memo- ry, press the MEMORY button until the M disappears from the screen.

•You may only set the real-time counter to zero at one location at a time. If you set the real-time counter to zero at a second loca- tion, the previous real-time counter to zero setting will be erased.

Image 54

Contents VRA471AT This bolt of lightning indi- cates uninsulated material Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoFeatures IntroductionTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Removing the Plastic Cover from the Front PanelHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System Recording/Viewing Any ChannelRecording One Channel/Watching Another Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Cable Box/DBSHookups With a Stereo TV Turning on Your VCR 2Turn on the TVPress the Menu button. The display shown below will appear Automatic Channel Setup Press the VCR button Press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsReviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Do each step within 60 seconds of the previous stepSetting the Clock cont’d Automatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Language Selection Setting the Remote to Operate a TV 2TV codeCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Menu Button REWind/ ButtonRECord/OTR Button Number ButtonsIf you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape Press the Eject button to remove the tapeRecording Turn on the TV and set it to channel 3 or 4, whicheverIf the VCR light appears on the display panel, go to . If One-Touch Recording OTR CH12Recording One Channel/Watching Another Timer Recording DailyTimer Recording cont’d Timer Recording cont’d Tape SpeedsChecking or Cancelling Timer Recordings See page 56 for more hintsSetting Up the VCR Plus+ Programming System ChannelsCall Letters Setting Up the VCR Plus+ Programming System cont’d Examine the lists onTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Auto DBS RecordLink Set the program to Be recorded on the satellite tunerRerecording Tape Duplication RF coaxial cableRepeat Play Press the PLAY/o button or the STOP/p button to selectPress the F.FWD/B button so that on appears beside Automatic Operation Features Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Playing a Tape at Double SpeedDuring tape playback, press the PAUSE/STILL button. a Viewing a Still PictureViewing a Slow Motion Picture Still picture will appear on the screenTV and Cable Box/DBS feature buttons of the remote When Child Lock is activatedDuring the timer recording Child LockIf another remote control beeps Letting your VCR find your remote for youPress the Mute button, then press the PAUSE/STILL button Time Search Press the VCR button Press the Time Search buttonExample Press the VCR button Press the Index Search buttonRecord End Search Skip SearchQuick Search To resume normal tape playback, press the PLAY/o buttonClear button to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Model # Serial #Timer PowerRemote control AutomaticPage Page Supplied Accessories