Philips VRA471AT owner manual Setting the Remote to Operate a TV, 2TV code

Page 21

Setting the Remote to Operate a TV 21

Your VCR remote control may operate your TV. If the remote control doesn’t operate your TV now, follow the steps below.

1

Point the remote control at your TV and press the TV button. Then, press the POWER button. If your TV turns on or off, try the other TV buttons (see pages 23-25). If your TV doesn’t turn on or off, or if the other buttons don’t work, go to step 2.

2

Find the brand of your TV on the list below, and remem- ber the two-digit number beside it.

TV CODES

1&6		Find your
1&6		2TV code.
POWER		EJECT
VCR/TV	SPEED	MEMORY
REC/OTR		PAUSE/STILL
	PLAY
REW		F.FWD
	STOP
MENU	STATUS/EXIT	CLEAR

1 2 3

CH.

4 5 6

EMERSON	. . . . . .14	PHILCO	. . . . . .14
FISHER	. . . . . .11	PHILIPS	. . . . . .01
GE	. . . . . .10	PHILIPS MAGNAVOX.	.01, 02, 03
GOLDSTAR	. . . . . .04	QUASAR	. . . . . .07
HITACHI	. . . . . .12	RCA	. . . . . .10
JVC	. . . . . .05	SAMSUNG	. . . . . .17
MAGNAVOX	01, 02, 03	SANYO	. . . . . .11
MARANTZ	. . . . . .13	SEARS	. . .08, 11
MITSUBISHI	. . . . . .13	SHARP	. . . . . .16
MONTGOMERY WARD . . . .14		SONY	. . . . . .09
PANASONIC	. . . . . .07	TOSHIBA	. . . . . .08
PANASONIC-GAOO .	. . . . . .07	ZENITH	. . .06, 15

3	7	8
	MUTE	0
	VCR	TV

VAR.SLOW

TRACKING

QUICK TIME

9

ALT.CH

VOL.

CBL/DBS

VCR PLUS+

/ENTER SLOW

F.ADV

X2 PLAY

INDEX REC END SKIP

SEARCH

5

4

3

Press the MUTE button.

4

Within 30 seconds, press the TV button.

5

Within 30 seconds, press the Number buttons to enter the two-digit code for your TV brand. For example, if you have a Zenith TV, press Number buttons 0, 6.

6

Repeat step 1. If the remote control works your TV, you’re fin- ished. If the remote control still doesn’t work your TV, repeat steps 3-5, using a different code for your brand (if available).

There is no guarantee that the

remote will work your TV.

1&6

Helpful Hints

•The remote control may only operate some features of your TV. For exam- ple, the remote control may turn on the TV power, but it may not change channels at the TV.

•If you can not change the channels at the TV using the Number but- tons, press the VCR PLUS+/ENTER button after you press the Number buttons. It may change channels at the TV.

•When you replace the batteries in the remote control, you must pro- gram the remote control again.

•Remember to point the remote con- trol toward the TV during steps 1-6.

Image 21

Contents VRA471AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoIntroduction FeaturesTable of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front PanelDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dHookups With a Cable Box/Direct Broadcast System Cable Signal RF coaxialConnections Recording/Viewing Any ChannelConnect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Turning on Your VCR 2Turn on the TVPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsDo each step within 60 seconds of the previous step Manual Clock SettingSetting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock SettingTime Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TVCable BOX Codes Remote Control Buttons Remote Control Buttons cont’d RECord/OTR Button REWind/ ButtonMenu Button Number ButtonsStatus Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Press the Eject button to remove the tapeRecording Turn on the TV and set it to channel 3 or 4, whicheverIf the VCR light appears on the display panel, go to . If OTR CH12 One-Touch RecordingRecording One Channel/Watching Another Daily Timer RecordingTimer Recording cont’d Tape Speeds Timer Recording cont’dSee page 56 for more hints Checking or Cancelling Timer RecordingsSetting Up the VCR Plus+ Programming System ChannelsCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’dTimer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLinkRF coaxial cable Rerecording Tape DuplicationRepeat Play Press the PLAY/o button or the STOP/p button to selectPress the F.FWD/B button so that on appears beside Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Playing a Tape at Double SpeedViewing a Slow Motion Picture Viewing a Still PictureDuring tape playback, press the PAUSE/STILL button. a Still picture will appear on the screenDuring the timer recording When Child Lock is activatedTV and Cable Box/DBS feature buttons of the remote Child LockIf another remote control beeps Letting your VCR find your remote for youPress the Mute button, then press the PAUSE/STILL button Press the VCR button Press the Time Search button Time SearchPress the VCR button Press the Index Search button ExampleSkip Search Record End SearchTo resume normal tape playback, press the PLAY/o button Quick SearchClear button to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyRemote control PowerTimer AutomaticPage Page Supplied Accessories