Baby Trend 1304TW manual To remove parent Tray, pull upward on the tray

Page 3

Screws

Front Wheels

Parent Tray

Rear Wheels

Stroller

TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ASSEMBLY:

 

 

 

• Remove stroller from box. The front wheels, rear wheels, parent tray, and support

 

 

 

bars specific to your infant car seats need to be installed prior to use.

 

 

To attach the front wheels, unfold stroller as described in the section following.

 

 

 

See figure 1.

 

 

 

 

Lean the stroller backwards so that it rests on the handle and rear frame tubes and

 

 

 

the front wheel tubes are pointing upward.

 

 

Fig. 1

 

Position the front wheel assembly at the front tube such that the large hole in the

 

 

swivel assembly will slide onto the front tube. Push each front wheel assembly

 

 

 

onto the front tube being careful that wheel assembly locks onto the front leg.

 

 

 

Pull on the wheel assembly to ensure that it is securely attached to the stroller.

 

 

 

Please see figure 2.

 

 

 

Lean the stroller forward to rest on the front wheels. To attach the rear wheels,

 

Fig. 2

 

position the rear axle and wheel assembly such that the brake levers are facing to

 

 

the rear of the stroller. Press the rear wheel assembly onto the rear frame tubes

 

 

 

being careful that the push buttons on the forward side of each rear tube engage

 

 

 

the hole on the forward side of each rear wheel housing. Pull on the rear wheel

 

 

 

assembly to ensure that it is securely attached to the stroller. Please see

 

 

 

figure 3a.

 

 

 

 

Ensure that the wheels are firmly locked into place. Do Not use the stroller if

 

Fig. 3a

 

the wheels are not locked into place, but rather contact our customer service

 

 

 

 

 

department immediately at (800) 328-7363, between the hours of 8:00am and 4:

 

 

 

30pm PCT, for assistance

 

 

 

To attach the storage basket, slide the U-shaped basket tube into the tubes at the

 

 

 

rear of the stroller. Push the tube in until the snap button pops through the hole

 

 

 

on the female tube. Please see figure 3b.

 

 

 

To attach the parent tray, position the tray so that the warning statement on the

 

Fig. 3b

 

inside can be read from the normal position of pushing the stroller. Push the

 

 

 

tray male end fittings into the

 

 

 

 

plastic female fittings on the

 

 

 

 

inside of the stroller handle.

 

 

 

 

Check that the tray is securely

 

 

 

 

latched in place. Please see

 

 

 

 

figure 4. To remove parent

 

 

 

 

tray, pull upward on the tray.

 

 

 

 

Fig. 6

Fig. 5

Fig. 4

3

Image 3
Contents Double Snap N Go Double Snap N Go To remove parent Tray, pull upward on the tray To Fold Stroller Stop Bar A1 Bar B1 With sleeve Bar C Bar D Position Table FrontBar B2 Bar A2 Car Seat Straps Screws RearInsertion of the Century Vante Infant Car Seat Installation Instructions for Century VanteFront Seat Rear SeatInstallation Instructions for Cosco Designer/Opus Insertion of the Cosco Designer/Opus 35 Infant Car SeatRemoval of the Cosco Designer/Opus 35 Infant Car Seat Installation Instructions for Evenflo Cozy Carry Insertion of the Evenflo Cozy Carry Infant Car SeatRemoval of the Evenflo Cozy Carry Infant Car Seat Installation Instructions for Evenflo On My Way Insertion of the Evenflo On My Way Infant Car SeatRemoval of the Evenflo On My Way Infant Car Seat Installation Instructions for Graco Snug Ride Insertion of the Graco Snug Ride Infant Car SeatRemoval of the Graco Snug Ride Infant Car Seat Installation Instructions for Peg Perego Primo Viaggio Installation Instructions for Baby Trend Latch-Loc Insertion of the Latch-LocInfant Car SeatRemoval of the Latch-LocInfant Car Seat