Error Indicator

Error Indicator Led

At initial power up, each Beacon II board checks for system errors. The system error check involves checking the various temperature sensors to determine whether any of these sensors are shorted or open.

The system will pumpdown and cycle off and will not restart until the fault is cleared or the circuit breaker reset, for the following conditions:

-Suction sensor shorted, open or not installed

-Room temperature sensor shorted or not installed

-Pressure Transducer open or not installed

The system will pumpdown, cycle off and try to restart for these faults. Each try will be after the 4 minutes “Hold Off” period, for the following fault conditions:

-High pressure or low pressure cutout

-Oil pressure

After the fourth try, the Alarm contacts will be closed and an alarm message displayed on the LED. To clear

this condition, the system should be cycled through the “SERVICE MODE” after the correction is completed.

Evaporator Fans Shut Off

In some installations, it is desirable to shut off the evaporator fans periodically. This is easily accomplished

on Beacon II by wiring a single pole, single throw switch (SPST) between the terminals marked “SERVICE” and “COM” on the Beacon II board. Closing this switch will

cause the system to pumpdown and shut off.

ERROR CODES

E1 - Room temperature sensor shorted, open or not installed

E2 - Defrost temperature sensor shorted, open or not installed

E3 - Suction temperature sensor shorted, open or not installed

E4 - Suction pressure transducer shorted, open or not installed

E5 - Outdoor temperature sensor shorted

E6 - Low superheat

E7 - Compressor shut down

(high or low pressure switch open or oil pressure switch open)

E9 - Multi-in/multi-out wiring error

Air Defrost fan motors must be wired through the fan relay on the Beacon II board for this to be effective on Air Defrost systems. The entire system will be shut off and remain off until the SPST switch is opened.

Air Defrost evaporator fans are setup to run constantly. If there is a need to shut down the evaporator fans on an Air Defrost system, this can be accomplished by wiring the evaporator fan motor or evaporator fan motor contactor through the fan relay on the Beacon II board.

When this is done and the Air Defrost system is placed in “SERVICE,” the evaporator fans will shut off when the system is in pumpdown.

19

Page 19
Image 19
Heatcraft Refrigeration Products H-IM-79E manual Error Indicator Led, Evaporator Fans Shut Off

H-IM-79E specifications

Heatcraft Refrigeration Products has long been a leader in eco-friendly and efficient cooling solutions, and the H-IM-79E is a prime example of their commitment to innovation and sustainability. Designed for commercial use, the H-IM-79E is a high-performance refrigeration unit ideal for supermarkets, convenience stores, and restaurants, where reliable temperature control is essential.

One of the standout features of the H-IM-79E is its energy efficiency. This unit employs advanced compressor technology that optimizes power consumption without sacrificing cooling performance. In addition, it is designed to minimize operational costs, making it an attractive option for businesses looking to reduce their energy bills while maintaining high standards of refrigeration.

The H-IM-79E integrates a robust refrigerant management system that uses environmentally friendly refrigerants, aligning with Heatcraft's commitment to reducing the carbon footprint of their products. This not only helps businesses comply with environmental regulations but also promotes a healthier planet for future generations.

Another key characteristic of the H-IM-79E is its superior temperature stability. The unit is equipped with precision temperature control technology that ensures consistent cooling performance, preventing temperature fluctuations that can compromise food quality and safety. This reliability is crucial in commercial settings where maintaining optimal storage conditions is essential.

The design of the H-IM-79E is also noteworthy. It features a compact footprint, allowing it to fit seamlessly into various commercial environments without taking up valuable floor space. Additionally, the unit is built with durable materials, ensuring longevity and minimizing maintenance needs.

User-friendly interfaces make the H-IM-79E easy to operate. It includes advanced monitoring and diagnostics capabilities, allowing business owners to track performance in real-time and address potential issues before they escalate. The incorporation of smart technologies means that operators can remotely monitor and control the system, providing flexibility and peace of mind.

In summary, the Heatcraft Refrigeration Products H-IM-79E stands out for its energy efficiency, eco-friendly refrigerant use, reliable temperature control, compact design, and user-friendly features. This combination of attributes makes it an ideal choice for businesses that prioritize both sustainability and performance in their refrigeration needs.