AMX MAX-CSE, MAX-CSD 10 manual Obtaining the IP information for a target Modero, SAP Settings

Page 36

MAX-CSE Web Interface

Stream Profiles Page Features (Cont.)

Feature

Description

 

 

• Target Address

The IP Address of the target IP-capable device that will receive the encoded outgoing

 

media stream. This is the IP of the target device such as the VG-Series Modero panel,

 

MAX-CSD10, or computer which will display the stream.

 

• Target Address must be in IPv4 dot notation (ex: X.X.X.X).

 

• Default IP Address is: 239.168.42.108 (a multicast address).

 

Obtaining the IP information for a target Modero:

 

1) Press the grey Front Setup Access button for 3 seconds to open the Setup page.

 

2) Press the Protected Setup button (located on the lower-left of the panel page) to

 

open the Protected Setup page and display an on-screen keypad.

 

3) Enter 1988 into the Keypad’s password field and press Done when finished.

 

4) Press the NetLinx Settings button to open the NetLinx Settings page and obtain IP

 

from the IP Settings section of this page.

 

Obtaining the IP information for a target PC:

 

1) On your PC, click Start > Run to open the Run dialog.

 

2) Enter cmd into the Open field and click OK to open the command DOS prompt.

 

3) From the C:\> command line, enter ipconfig to display the current IP Address of the

 

PC.

 

 

• Target Port (video)

The port on the destination device where the outgoing video stream is being directed to.

 

This value can be from 0001 - 9999 (default is 5000).

 

If using UDP as a Transport Protocol, this is also the port where the combined audio/

 

video stream is sent.

 

Note: If using RTP it is strongly recommended that this port number be an even value.

 

Using odd numbered port values will cause the stream to not be properly recognized

 

by the target Modero panel.

 

Note: It is recommended that the following ports not be used: 21, 22, 23, 80, 443, and

 

1319.

• Target Audio Port

 

The port on the destination device where the audio only portion of the stream is being

 

directed to. This value can be from 0001 - 9999 (default is 5002).

 

• If using UDP as a Transport Protocol, this field becomes greyed-out and unused since

 

the both the audio and video content is being combined into a single stream.

 

Note: If using RTP (split streams) it is strongly recommended that this port number be

 

an even value.

 

• If the target is a Modero VG-Series panel, the Target Audio Port field must always

 

increment the value of the Target video port by 2. Example: Target Port = 5000,

 

Target Audio Port = 5002.

 

 

SAP Settings:

In SAP mode, the user selects a video stream from a list. Once selected the decoder

 

will automatically connect to the stream server and begin decoding.

 

 

• SAP Mode

Use these radio button to enable/disable SAP mode (default = enabled).

 

 

• IP Configuration

Select an IP Configuration from the drop-down menu (Default or Other). By default,

 

Default is selected (the default multicast IP address will be used). Note that if you select

 

Other, the following two additional fields are enabled:

Alternate IP Address Enter the alternative Multicast IP address that will be used to send the SAP packets. (Only available if Other is selected as the IP Configuration for SAP Mode).

• Alternate IP Port

Enter the alternative Multicast IP port that will be used to send the SAP packets.

 

(Only available if Other is selected as the IP Configuration for SAP Mode).

These profiles take effect on the MAX-CSE only after pressing the on-screen Apply button.

The UDP Transport Protocol only supports the use of the MPEG-2 codec, whereas the RTP Transport Protocol can support using both MPEG-2 and MPEG-4 codecs.

30

MAX-CSE/MAX-CSD10 Operation/Reference Guide

Image 36
Contents MAX-CSE/MAX-CSD10 AMX Limited Warranty and Disclaimer Table of Contents MAX-CSD10 Web Interface Configuration and Firmware Update Page MAX Encoder Features MAX-CSE Video EncoderOverview MAX-CSE FG2178-70 ComponentsMAX-CSE Product Specifications MAX-CSE SpecificationsWhile in IR mode Sensing for IR ports MAX-CSD10 Product Specifications MAX Decoder FeaturesMAX-CSD10 Video Decoder MAX-CSD10 FG2178-72 ComponentsMAX-CSD10 FG2178-72 Specifications AACMAX-CSD10 Specifications Page MAX-CSE and MAX-CSD10 Installation MAX-CSE and MAX-CSD10 Connections and WiringWiring Guidelines Direct Power Port Assignments and FunctionalityWiring length guidelines Preparing captive wiresWiring a power connection Wiring Guidelines Indirect Power via PoEPoE Special wiring instructions CSE MAX-CSEWiring the MAX-CSE connectors and cables VDC power SupplyEthernet/RJ-45 Port Connections and Wiring Ethernet RJ-45 Pinouts and SignalsSignals Connection Pairing Color MICPower over Ethernet PoE wiring DB9 Device Port Connections and WiringEthernet LEDs IR/Serial Port Connections and Wiring Input/Output I/O Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications Wiring the MAX-CSD10 connectors and cables Port Wiring SpecificationsPin Signal Function Installing Into an Equipment Rack Page Default Security Configuration MAX-CSE Web InterfaceSecurity Terms Security TermsDefault Security Configuration case-sensitive Administrator accountCommunicating with the unit via the browser-based UI MAX-CSE User Interface Overview and Features User Interface FeaturesFeature Description Navigation Bar Browser-based UI Application OverviewAdministration Page Features Feature DescriptionStream Status Administration AdministrationFeature Description Resources Example Computer CourseChanging the Program Description ModeUpload Firmware Click Upload a File Click Reboot done. Upload a File Upgrading New FirmwareStream Profiles Stream ProfilesStream Profiles Page Features Feature Description Encoder ProfileVideo Resolution AudioSVCD, MP3 StreamSAP Settings Obtaining the IP information for a target ModeroChanging the Encoder Profile Encoder Profiles and ParametersVCR Set up Set up Page FeaturesFeature Description Video NetLinx Settings Changing Video and Audio SettingsNetLinx Settings Page Features Feature Description NetLinx MasterIP Settings Changing the NetLinx Master ConnectionChanging the IP Settings IP Settings Page FeaturesFeature Description IP Address DNS AddressUser Page Features Feature Description UserUser Changing User Settings MAX-CSD10 User Interface Overview and Features Feature Description Browser Address fieldMAX-CSD10 Web Interface Navigation frameFeature Description Stream Status frame LogoffActive Page frame Communicating With The Unit Via the Browser-based UI Updating FirmwareStream Selector Page Features Stream SelectorStream Set-up Page Features Stream Set-upChanging the stream configuration Setting up an SAP stream configurationSetting up an Rtsp stream configuration Setting up a Manual stream configuration Stream Configuration Page Manual ModeAudio/Video Page Features NetLinx Page FeaturesAudio/Video NetLinxTo make changes to the IP Settings To change the User Login Settings User Page DetailsConfiguring Communication Reading the Front Panel LCDConfiguring the MAX Communication Parameters Obtaining the unit’s initial Dhcp AddressSave login profile selection box Communicating with the Target Master via an IP Assigning Master Communication Settings and TCP/IP Settings Associating the MAX unit to a Target Master Associating a MAX-CSE to a Target MasterStudio Online Tree tab showing the communicating MAX unit Changing the MAX’s Device Number Associating a MAX-CSD10 Unit to a Target MasterChanging the MAX-CSE device number via the UI Changing the MAX-CSE device number via StudioUsing the ID button to change the MAX-CSE’s Device Value Recommended NetLinx Device numbersChanging the MAX-CSD10 device number via the UI Configuration and Firmware Update Before You BeginMAX vs. NetLinx Master Functional Overlap Verifying the MAX’s current version of Firmware via the UIUpgrading MAX Firmware Verifying the MAX’s current version of Firmware via StudioUpgrading MAX-CSE Firmware via the UI Upgrading MAX-CSD10 Firmware via the UI Upgrading the MAX’s Firmware via NetLinx StudioClick Close once the download process is complete Displaying Stream Content Requirements for Receiving Streamed ContentSetting up a Modero Panel to Receive and Display a Stream Obtaining the IP Address of the target panelConfiguring the MAX-CSE for communication System SettingsStream Profiles Configuring the MAX-CSE audio/video inputs V SetupSetting up a streaming page within TPDesign4 Rtpmpeg#//IP Address of MAX-CSETarget Video Port Video Adjustment page showing default values Establishing the final connection between the two unitsSetting up a Computer to Receive and Display a Stream Configure the MAX-CSE for communication to a computerObtaining the IP Address of the target computer Displaying Stream Content RTP Video Stream Component RTP Audio Stream Component Page NetLinx Programming DevicePortSystem DPSPort Assignments Port/DescriptionMAX-CSE Streaming Commands Port MAX-CSE Streaming SendCommandsCommand Description GET AsourceGET SAP IP Mode GET FormatGET Gain GET SAPGET Session Info GET Session ListGET Stream Status GET URL GET VideoGET Video Port Status GET Vsource PlaySET Asource SET AudioSET SAP IP Mode SET FormatSET Gain SET SAPSendcommand ENCODER,SET Video MPEG2 D1 6000 CBR SET URLSET Video MAX-CSD Streaming Commands Port MAX-CSD Streaming SendCommandsSET Vsource StopGET Control Mode GET Rtsp ServerGET Session Cursor Sendcommand DECODER, GET Session Info 1 Title Sendcommand DECODER, GET Session Info 2 TitleSendcommand DECODER, GET Session Info 2 MEDIA1 Sendcommand DECODER, GET Session Info 2 MEDIA2Sendcommand DECODER,GET URL Sendcommand DECODER,GET VideoSendcommand DECODER, Play Sendcommand DECODER,SET Audio MP3SET Control Mode Sendcommand DECODER, SET Control Mode SAPSendcommand DECODER,SET Format PAL Sendcommand DECODER, SET SAP IP Mode ALTSendcommand DECODER, SET Sesson Cursor Sendcommand DECODER,SET URL UDP 224.0.0.1Sendcommand DECODER,SET Video MPEG2 SET Session CursorRS-232/422/485 SendCommands Port RS-232/422/485 SendCommandsChardm CtspshCtspsh OFF GET BaudRxoff RxonSET Baud Tset BaudRS232/422/485 Ports Channels RS232/422/485 Ports ChannelsTxclr XoffRS-232/422/485 SendString Escape Sequences Port RS-232/422/485 SendString Escape SequencesIR/Serial Port Port 3 Commands IR/Serial SendCommandsIR / Serial Ports Channels IR / Serial Ports ChannelsGET Mode CtofCton Iroff PODPOF PONPtof PtonSET IO Link SET Mode Sendcommand IR1,SET Mode IRSendcommand IR1, SP,25 Short cable length 10 feetSendcommand DEV,XCHM extended channel mode Sendcommand IR1,XCHMSendcommand IR1,XCH XchmPort Commands Port Send CommandsIR RX Port Channels Port GET InputLCD Commands Port BacklightBACKLIGHT-0 BACKLIGHT-50Page Programming MAX-CSE/MAX-CSD10 Operation/Reference Guide 103 It’s Your World Take Control
Related manuals
Manual 2 pages 62.62 Kb Manual 116 pages 15.94 Kb

MAX-CSD 10, MAX-CSE specifications

The AMX MAX-CSE and MAX-CSD 10 are advanced multimedia presentation systems designed to enhance communication and collaboration in various professional environments. These devices are tailored for modern conference rooms, educational institutions, and corporate settings, providing seamless integration of audio-visual technology to facilitate effective presentations and meetings.

One of the standout features of the MAX-CSE and MAX-CSD 10 is their sophisticated audio and video processing capabilities. The MAX-CSE serves as a central management hub, supporting high-definition video outputs and multiple input sources, including HDMI, VGA, and wireless connectivity options. This versatility ensures that users can connect a wide array of devices—laptops, tablets, and smartphones—without hassle and quickly switch between them during presentations.

The MAX-CSD 10 complements the MAX-CSE as a dedicated audio unit equipped with powerful amplification and precise tuning. It delivers clear and balanced sound, even in larger rooms, ensuring that every participant can engage fully, regardless of their location in the space. With features like echo cancellation and noise reduction technology, the MAX-CSD 10 enhances voice clarity, making it ideal for video conferencing and webinars.

An important characteristic of the AMX MAX series is their user-friendly interface. The systems are designed for intuitive operation, enabling users to control various settings with ease, whether they are tech-savvy or not. The touch panel interface can be customized to meet specific needs, allowing quick access to essential functions such as lighting, video routing, and audio control.

In terms of connectivity, both systems are equipped with robust network capability, allowing integration with existing IT infrastructure. This feature ensures that users can manage and control the systems remotely through a web interface or compatible applications, enhancing productivity and easing the overall user experience.

Robust security measures are also a significant aspect of the AMX MAX-CSE and MAX-CSD 10 systems. They are designed with advanced encryption and user authentication protocols, ensuring that sensitive data remains protected during presentations and meetings.

In conclusion, the AMX MAX-CSE and MAX-CSD 10 multimedia presentation systems stand out in the market due to their superior audio and video quality, user-friendly features, and extensive connectivity options. They are ideal solutions for professionals seeking to leverage technology for more productive and engaging communication.