Graco ISPA118AC manual Using Latch to install Base, For ease of installation, extend Latch

Page 67

6.4 Using LATCH to install Base

1.

For ease of installation, extend LATCH

Tongue

 

to its maximum length.

 

2.

Position base in vehicle seat as

 

 

shown.

 

3.

Thread LATCH through base belt

 

 

path normally used for vehicle seat

 

 

belt. Make sure that LATCH is UNDER

 

 

tongue on base .

 

 

Belt must lay flat and not be twisted.

 

4.

Hook Connectors to vehicle lower

 

 

anchors. Pull firmly on Connectors to

 

 

be sure they are attached .

 

5.

Tighten LATCH by pushing down

 

 

hard on base and pulling the

 

 

adjustment belt .

 

6. NEVER put two LATCH connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle manufacturer .

7. Test infant restraint for secure installation as described in infant restraint “Final Safety Check” p.34.

8.Check that the LATCH stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Customer Service.

31

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Manual DEL Propietario Adult Assembly Required Using Graco Infant CAR Seat with Stroller Lbs dans la pochette de baldaquin sur certains modèles Lenfant Peut Glisser Dans LES Ouvertures DES ET S’ÉTRANGLER Kg 3 libras sobre la bandeja USO DEL Transportador Para Bebé Graco CON EL Cochecito Verifique que tiene Parts list Liste des pièces Lista de las piezasMise EN Garde Advertencia Footrest Le repose-pied ReposapiésTo Open Stroller Ouvrir la poussette Cómo abrir el cochecito Basket Le panier La canasta Front Wheels Roues avant Ruedas delanteras Rear Axle L’essieu arrière El eje trasero Rear Wheels Roues arrières Ruedas traseras Snap Enclenchez ¡RUIDO Parent Tray Le plateau pour adulte Bandeja para padres Mise EN Garde Child’s Tray Le plateau pour enfant Bandeja para niñosSnap Basket Le panier La canasta Swivel Wheels Roues pivotantes Ruedas giratorias Brakes Freins FrenosTo Secure Child Pour attacher l’enfant Cómo asegurar al niño Point Buckle Boucle à 3 point Hebilla de 3 puntos Page Mise EN Garde To Recline Seat Réglage du dossier Cómo ajustar el respaldoPara levantarla, tire la correa Mise EN Garde Page To Fold Stroller Pour replier Para plegar el cochecito ➊ ➌Page Snap Over CAR Seat To remove car seat unlock latches Care and Maintenance Soins et entretien Atención y mantenimiento Or/ó Infant Restraint Carrier Do not install or use This infant restraint until youImportant Information Additional Information Properly securing your child in the infant restraint Your child’s safety depends onProperly reclining the infant restraint Properly routing the vehicle seat belt or LatchIt today Registration InformationRegister Your Infant Restraint Recall InformationIf You Need Help Front View Features and ComponentsRear View Removing and Attaching Base Adjusting HandleNever use positions B or C in the vehicle Attaching Canopy Head Support on certain models Do not Place this Infant Restraint in a Vehicle Important InformationNever Leave Your Child Unattended Page Additional Warnings for Use as Carrier Weight 5-22 lbs .3-10 kg Height 29 inches 73 cm or less Height and Weight LimitsYour child Must meet all requirements Watch the child. If the driver is the only Infant Restraint LocationVehicle Seat Requirements Whenever possible, secure the infantVehicle seat must face forward Vehicle Seat Belt RequirementsPassive Restraint Lap Belt with Motorized Shoulder Belt Unsafe Vehicle Belt SystemsLap Belts Forward of Seat Crease Lap Belts with Automatic Locking Retractor ALR Safe Vehicle Belt SystemsConnect lap and shoulder belts with locking clip as shown To Install Locking ClipLatch Locations Visible, they may be marked with the symbolHarness straps to other harness slots Using Infant RestraintPositioning Harness Straps Sudden stop or crashCheck that straps are not twisted Thread straps through tighteners exactly as shownSecuring Child in Infant Restraint Safety Check Installing the Infant Restraint/Base Using Vehicle Belt Base with seat belt Thread the seat beltInfant restraint with seat belt Page For ease of installation, extend Latch Using Latch to install BaseReclining Infant Restraint/Base When using the base Final Safety Check Every time you drive with your child Use only in forward-facing aircraft seat Additional InformationAirplane Use Storing LatchCleaning and Maintenance Replacement Parts Asiento de Seguridad infantil Portabebés Funciones y componentes Ubicación del sistema de seguridad para niños Instalación del sistema de seguridad para niños/baseDe su vehículo Advertencias a padres y otros usuariosEl mismo Graco Children’s Products Inc Información sobre el registroCanadá 1-800-667-8184 Montreal Si necesita ayudaVista Delantera Funciones y componentesVista Trasera Ajuste de la manija Sacar y conectar la baseAmbos botones de ajuste de Para quitar la capota, siga los pasos al revés Colocación de la capotaApoyacabezas en ciertos modelos Advertencias para uso como sistema de seguridad para niños Información importanteInfla, puede golpear al niño y al sistema de Nunca Deje a SU Niño Solo Conoce su historia Advertencias para el uso con un cochecitoNo cuelgue cordones sobre o encima del transportador Advertencias adicionales para el uso como transportadorNo ponga cordones a los juguetes Su niño Debe cumplir con todos los requisitos Limitaciones de peso y estaturaCuando sea posible, sujete el sistema Ubicación del sistema de seguridad para niñosRequisitos del cinturón de seguridad del vehículo Emergency Locking Retractor, ELR El LatchCinturón de seguridad abdominal con Sistemas Seguros de cinturones de vehículosPara instalar la traba de seguridad Ubicación del Latch Colocación de las correas del arnés Usar el asiento de seguridad infantilVerificación DE Seguridad Saque la correa de la ranuraSujetar el niño en el sistema de seguridad para niños Verifique que las correas del arnés no estén dobladas 18 a Sistema de seguridad para niños con cinturón de seguridad Pase el cinturón de seguridadPage Uso del Latch para instalar la base Inclinación del sistema de seguridad para niños/base Zona de color azul Cuando usa la basePara niños Uso en aviones Información adicionalLa Hebilla puede limpiarse con un trapo húmedo Limpieza y mantenimientoPiezas de repuesto

ISPA118AC specifications

The Graco ISPA118AC is a powerful and versatile airless paint sprayer designed for both DIY enthusiasts and professional painters. This advanced equipment streamlines the painting process, making it faster and more efficient. One of its standout features is the ProXChange pump technology, which enables users to quickly switch out the pump without any tools, minimizing downtime and maximizing productivity on the job site.

Equipped with a robust 1.2 HP motor, the Graco ISPA118AC delivers an impressive maximum pressure of 3,000 PSI. This high pressure allows for a smooth and even finish, making it suitable for a variety of projects, from small touch-ups to large-scale exterior painting. Its 5/8-inch diameter hose ensures excellent paint flow and minimizes pressure loss, which further enhances its spraying performance.

The ISPA118AC also boasts a reversible spray tip, allowing for easy unclogging during use. If debris gets stuck, simply reverse the tip, and the flow of paint will clear the blockage, ensuring continuous operation without interruptions. This feature is particularly useful when working with thicker paints or when painting textured surfaces.

Another important characteristic of the Graco ISPA118AC is its lightweight and compact design. Weighing in at just 32 pounds, it is easy to transport and maneuver on job sites, making it a practical choice for contractors and home users alike. The integrated carry handle adds further convenience, allowing for effortless lifting and movement.

The Graco ISPA118AC is engineered with user-friendly controls, providing an intuitive experience for users of all skill levels. The adjustable pressure control enables painters to customize the spray for different surfaces and materials. Additionally, the large paint bucket helps minimize the need for frequent refills, allowing users to cover larger areas without constant interruptions.

In summary, the Graco ISPA118AC is an exceptional choice for anyone looking to achieve a professional-grade finish with ease. With its powerful motor, versatile technologies, and user-friendly features, this airless paint sprayer delivers outstanding performance and reliability, making it a valuable addition to any painting toolkit.
Top Page Image Contents