Arcam AVR100 manual Troubleshooting, Problem Cause Solution

Page 15

Troubleshooting

The following table should help you diagnose most problems that may arise when using the AVR100.

Problem

Cause

Solution

No audio

1.

Power Lead unplugged or not switched on

1.

Check mains lead is connected to AVR100 and that the

 

 

 

 

wall switch is on

 

2.

In stand by mode

2.

Press the POWER/STANDBY button on remote handset

 

3.

Mute on

3.

Switch mute off

 

4.

Tape monitor selected

4.

Press the TAPE MONITOR button

No sound on one

1.

Loudspeaker not connected or not connected properly

1.

Check connections to AVR100 and to loudspeaker

channel

2.

Input not connected or not connected properly

2.

Check connections to AVR100 and at source

 

3.

Speaker described as ‘OFF’ in set up page

3.

Re-assign speaker settings in on-screen display

 

4.

Channel level set too low

4.

Re-assign channel balance in on-screen display

Dolby Digital or DTS

 

Digital input not connected

 

Connect digital output of source to appropriate input on

not auto detected

 

 

 

AVR100

Lack of bass or poor

1.

Speakers wired out of phase (i.e. + connected to –, or red

1.

Check all connections to AVR100 and to loudspeakers

stereo image

 

to black in error – a polarity error in one speaker)

2.

Re-select preset speaker settings in on-screen display

 

2.

Speakers set as SMALL

 

 

No sound from tuner

1.

Aerial not connected properly

1.

Check aerial connections to AVR100’s back panel

 

2.

Weak signal muted by FM Mute

2.

Switch FM MUTE/MONO off or re-tune station

Remote control not

1.

Batteries in handset fitted the wrong way round or flat

1.

Check orientation of batteries/ replace discharged

working

2.

IR receiver window on AVR100 is obscured

 

batteries

 

3.

IR receiver window flooded with light

2.

Remove obstruction

 

 

 

3.

Move AVR100 away from light source or shade from

 

 

 

 

intense light source

Picture scrolls around

 

Wrong video system selected

 

To toggle between PAL and NTSC video systems, press

screen, or picture is

 

 

 

and hold the STORE button and click the SAT button.

only in black and white

 

 

 

 

No picture on monitor

1.

Source is not playing

1.

Check and play source

when video source is

2.

Video connection between the source and AVR100 is not

2.

Check system wiring: ensure connection between source

selected

 

been made

 

 

Sound and picture

 

System connections made to wrong inputs of AVR100

 

Check system wiring: ensure all connections are made to

come from different

 

 

 

correct input on AVR100

sources

 

 

 

 

AVR100 switches itself

 

Circuits have overheated and unit has been switched into

 

Switch unit off. Remove any restrictions to good airflow.

to stand by mode

 

protection mode. This may be because airflow around the

 

Allow unit to cool down before switching on again.

 

 

unit is restricted.

 

 

The red status LED

 

The AVR100 has gone into protection mode. This is

1.

Turn the AVR100 off and disconnect the mains cable.

flashes and the

 

probably caused by an overload or short circuit on the

2.

Check all the wiring, making sure that no bare

AVR100 appears not to

 

loudspeaker outputs.

 

loudspeaker cables are touching each other or the

work.

 

 

 

chassis.

 

 

 

3.

Reconnect the mains cable and switch back on.

 

 

 

 

If this does not cure the problem or the problem persists

 

 

 

 

contact your Arcam dealer.

 

 

 

 

 

AVR100

E n g l i s h

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Arcam AVR100 surround sound receiver Safety guidelines Safety instructionsSafety compliance Using this handbook SafetyContents FM aerial InstallationSetting up the aerials Positioning the unitInterconnect cables Connecting inputsConnecting outputs Connecting to other equipmentConnecting to a power supply Channel balance Setting up Using the On Screen Display OSDSetup Input settingsDistance to listening position Your measure Channel delaysDifference Delay ms 6ftSpeaker settings Presets for typical speaker setupsNo subwoofer loudspeaker? EXT Using the AVR100Front panel controls Input selectionDeleting an unused preset Using the tunerTuning to a station Storing a presetRDS Radio Data System FM Mute/MonoRadio interference CR-340 Remote Control Using the remote controlReference Bi-wiring and bi-amping loudspeakers Bi-wiring your loudspeakersBefore you start Problem Cause Solution TroubleshootingTechnical specifications On line registration GuaranteeConsignes de sécurité Normes de sécuritéNorme de sécurité Utilisation de ce manuel SécuritéTable des matières Antenne AM Installation des antennesMise en place de l’AVR Antenne FMCâbles de branchement Branchement des entréesBranchement des sorties Branchement à d’autres appareilsBranchement à une alimentation électrique Channel Balance équilibrage des nivaux Setup RéglagesInput Setting Réglage des entrées Réglage Utilisation de l’affichage à l’écran OSDAvant gauche ou droit Mètres Centre Arrière gauche ou droit Channel Delays réglage du retard des canauxPar exemple Distance par rapport à Position d’écouteSpeaker Settings réglage des enceintes Preset Pré-réglages des enceintes acoustiques classiquesPas de caisson d’extrêmes graves? Commandes en façade Power AlimentationSélection d’entrée Annulation d’une présélection non utilisée Utilisation du tunerSélection d’une station Mémorisation d’une présélectionInterférences radio Système RDS Radio Data SystemNécessaires pour utiliser les lecteurs CD et DVD Arcam Utilisation de la télécommandeTélécommande CR-340 Volume et CoupureRéférence Avant de commenceBi-câblage des haut-parleurs Dépannage Problème Cause SolutionSpécifications techniques Enregistrement sur Internet GarantieSicherheitsrichtlinien SicherheitsrichtlinienEinhaltung von Sicherheitsbestimmungen Hinweise zum Handbuch SicherheitInhalt MW-Antenne Aufstellen des GerätesEinrichten der Antennen UKW-AntenneVerbindungskabel Anschließen der EingängeAnschließen der Ausgänge Anschließen anderer GeräteAnschließen der Stromversorgung Seite „SETUP Einrichten des Geräts Das On Screen Display OSDSeite „CHANNEL Balance Kanalbalance Abstand Seite „CHANNEL DelaysM z. B m Vorne links oder rechts Mitte Hinten links oder rechtsKein Subwoofer? Voreinstellungen für typische LautsprecherkombinationenAuswählen der Eingänge Surround Mode Surround-ModusDer AVR100 Steuerelemente an der VorderseiteSuchen eines Senders Der TunerStörungen FM MUTE/MONODie Fernbedienung CR-340 Die FernbedienungErste Schritte Bi-Wiring der LautsprecherFehlerbehebung Problem Ursache LösungTechnische Daten VerstärkerTuner Inanspruchnahme der Garantie ProblemeWeltweite Garantie Die Garantie umfasst FolgendesAVR100 G l i s h Issue

AVR100 specifications

The Arcam AVR100 is a high-performance AV receiver designed to provide immersive sound and video experiences for home theaters. Renowned for its exceptional audio quality, the AVR100 incorporates advanced technologies that elevate its performance in both music and movie playback.

One of the key features of the Arcam AVR100 is its high fidelity sound reproduction. Powered by the company's renowned Class G amplification, the AVR100 delivers a robust output while minimizing distortion. With a total power output of 100 watts per channel, it can drive a variety of speaker setups, making it suitable for both small and large home theaters. The integration of sophisticated digital signal processing allows for precise control over sound, ensuring that every nuance of audio is captured, whether it’s from movies or music.

The AVR100 supports multiple surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II, allowing users to enjoy a truly cinematic experience. The receiver's multichannel capability accommodates up to seven channels, providing an enveloping sound field that enhances the viewing experience. Additionally, users can customize the sound to their liking through the built-in room correction technology, which analyzes the acoustics of the listening environment and adjusts output accordingly.

Video capabilities are equally impressive, with the AVR100 providing multiple HDMI inputs that support high-definition video signals. This ensures compatibility with a range of modern devices, from Blu-ray players to gaming consoles. The inclusion of video upscaling technology enhances standard-definition content, allowing it to be viewed in near-HD quality, and providing a seamless integration with high-definition displays.

In terms of build quality, the AVR100 showcases Arcam’s commitment to craftsmanship. The solid construction minimizes vibrations and enhances durability, which is crucial for sustained performance over time. The user-friendly interface is designed to simplify navigation through settings and features, making it accessible for both audiophiles and casual users.

Connectivity options on the AVR100 are extensive, including multiple analog and digital inputs, allowing for a variety of source components to be connected. The receiver also supports mass storage devices and streaming services, catering to the demands of modern users who wish to access music and media easily.

Overall, the Arcam AVR100 stands out as a sophisticated AV receiver that balances powerful audio performance, versatility, and ease of use, making it an excellent choice for anyone seeking to create a premium home theater experience.
Top Page Image Contents