Arcam AVR100 Connecting outputs, Connecting to other equipment, Connecting to a power supply

Page 6

Connecting outputs

Connecting to other equipment

Monitor output

Both composite and S-video monitor outputs are provided for connection to the ‘Video line in’ of your TV, monitor, or projector. If you have both Composite and S-video inputs connected

to your AVR100 you need only connect the S-VIDEOMonitor Output to your TV (provided that your TV accepts an S-video input).

Connecting to a power supply

Wrong plug?

Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees with the voltage setting (120V or 230V) indicated on the rear panel of the unit.

If your mains supply voltage or mains plug is different, consult your Arcam dealer or Arcam Customer Support on +44 (0)1223 203203.

Loudspeaker outputs

Before connecting loudspeakers to your AVR100 you must set the Impedance switch on the rear to the correct position.

WARNING: Never adjust this switch with the power on or you will damage the AVR100.

If your loudspeakers are rated at 6Ω or lower set the switch to the 4–6Ωposition. If your loudspeakers are rated higher than 6Ω, set the switch to the 8Ω position.

WARNING: This unit should only be used with loudspeakers with an impedance rating between 4Ω and 8Ω.

The AVR100 is fitted with loudspeaker terminals in line with BFA (British Federation of Audio) standard specification. The terminal will accept spades, bare wire or a BFA plug. To connect spades or bare wires, unscrew the end of the terminal, insert the wire or spade and screw back up. Ensure that no stray strands of wire are allowed to touch other cables or the AVR100’s casing as this can cause a short circuit and damage the amplifier.

Bi-wiring and Bi-amping loudspeakers

Notes on these techniques are given in the Reference section of this handbook.

Preamplifier outputs

If you wish to upgrade your system by adding a power amplifier, always specify an Arcam unit to ensure matching gain.

The AVR100 has six line-level pre-amp outputs that can be connected to Arcam external power amplifiers to bi-amplify (‘bi-amp’) any of the channels. Alternatively, the AVR100 can be used solely as a preamplifier.

Depending on how your system is configured, the subwoofer PRE-AMP OUT should be connected using a line level interconnect, to either:

■an active subwoofer, or

■a power amplifier used to drive a passive subwoofer.

Headphone output

A 1/4” stereo jack socket is provided on the front panel for headphone listening. Inserting the jack socket automatically mutes the loudspeaker and pre-amp outputs from the AVR100.

Mains lead

The appliance is normally supplied with a moulded mains plug already fitted to the lead. If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Should you require a new mains lead, contact your Arcam dealer.

Plugging in

Push the plug (IEC line socket) of the power cable supplied with the unit into the socket (AC INLET) in the back of the unit. Make sure it is pushed in firmly.

Put the plug on the other end of the cable into your power supply socket and switch the socket on.

Non-use periods

If the unit is to be left unused for an extended period, we recommend that you switch the unit off from the front panel button, rather than use ‘stand by’ mode with the remote control.

AVR100

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Arcam AVR100 surround sound receiver Safety guidelines Safety instructionsSafety compliance Using this handbook SafetyContents Positioning the unit InstallationSetting up the aerials FM aerialConnecting inputs Interconnect cablesConnecting outputs Connecting to other equipmentConnecting to a power supply Input settings Setting up Using the On Screen Display OSDSetup Channel balance6ft Channel delaysDifference Delay ms Distance to listening position Your measureSpeaker settings Presets for typical speaker setupsNo subwoofer loudspeaker? Input selection Using the AVR100Front panel controls EXTStoring a preset Using the tunerTuning to a station Deleting an unused presetRDS Radio Data System FM Mute/MonoRadio interference Using the remote control CR-340 Remote ControlReference Bi-wiring and bi-amping loudspeakers Bi-wiring your loudspeakersBefore you start Troubleshooting Problem Cause SolutionTechnical specifications Guarantee On line registrationConsignes de sécurité Normes de sécuritéNorme de sécurité Utilisation de ce manuel SécuritéTable des matières Antenne FM Installation des antennesMise en place de l’AVR Antenne AMBranchement des entrées Câbles de branchementBranchement des sorties Branchement à d’autres appareilsBranchement à une alimentation électrique Réglage Utilisation de l’affichage à l’écran OSD Setup RéglagesInput Setting Réglage des entrées Channel Balance équilibrage des nivauxDistance par rapport à Position d’écoute Channel Delays réglage du retard des canauxPar exemple Avant gauche ou droit Mètres Centre Arrière gauche ou droitSpeaker Settings réglage des enceintes Preset Pré-réglages des enceintes acoustiques classiquesPas de caisson d’extrêmes graves? Commandes en façade Power AlimentationSélection d’entrée Mémorisation d’une présélection Utilisation du tunerSélection d’une station Annulation d’une présélection non utiliséeSystème RDS Radio Data System Interférences radioVolume et Coupure Utilisation de la télécommandeTélécommande CR-340 Nécessaires pour utiliser les lecteurs CD et DVD ArcamRéférence Avant de commenceBi-câblage des haut-parleurs Problème Cause Solution DépannageSpécifications techniques Garantie Enregistrement sur InternetSicherheitsrichtlinien SicherheitsrichtlinienEinhaltung von Sicherheitsbestimmungen Hinweise zum Handbuch SicherheitInhalt UKW-Antenne Aufstellen des GerätesEinrichten der Antennen MW-AntenneAnschließen der Eingänge VerbindungskabelAnschließen der Ausgänge Anschließen anderer GeräteAnschließen der Stromversorgung Seite „SETUP Einrichten des Geräts Das On Screen Display OSDSeite „CHANNEL Balance Kanalbalance Vorne links oder rechts Mitte Hinten links oder rechts Seite „CHANNEL DelaysM z. B m AbstandVoreinstellungen für typische Lautsprecherkombinationen Kein Subwoofer?Steuerelemente an der Vorderseite Surround Mode Surround-ModusDer AVR100 Auswählen der EingängeDer Tuner Suchen eines SendersFM MUTE/MONO StörungenDie Fernbedienung Die Fernbedienung CR-340Bi-Wiring der Lautsprecher Erste SchritteProblem Ursache Lösung FehlerbehebungTechnische Daten VerstärkerTuner Die Garantie umfasst Folgendes ProblemeWeltweite Garantie Inanspruchnahme der GarantieAVR100 G l i s h Issue

AVR100 specifications

The Arcam AVR100 is a high-performance AV receiver designed to provide immersive sound and video experiences for home theaters. Renowned for its exceptional audio quality, the AVR100 incorporates advanced technologies that elevate its performance in both music and movie playback.

One of the key features of the Arcam AVR100 is its high fidelity sound reproduction. Powered by the company's renowned Class G amplification, the AVR100 delivers a robust output while minimizing distortion. With a total power output of 100 watts per channel, it can drive a variety of speaker setups, making it suitable for both small and large home theaters. The integration of sophisticated digital signal processing allows for precise control over sound, ensuring that every nuance of audio is captured, whether it’s from movies or music.

The AVR100 supports multiple surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II, allowing users to enjoy a truly cinematic experience. The receiver's multichannel capability accommodates up to seven channels, providing an enveloping sound field that enhances the viewing experience. Additionally, users can customize the sound to their liking through the built-in room correction technology, which analyzes the acoustics of the listening environment and adjusts output accordingly.

Video capabilities are equally impressive, with the AVR100 providing multiple HDMI inputs that support high-definition video signals. This ensures compatibility with a range of modern devices, from Blu-ray players to gaming consoles. The inclusion of video upscaling technology enhances standard-definition content, allowing it to be viewed in near-HD quality, and providing a seamless integration with high-definition displays.

In terms of build quality, the AVR100 showcases Arcam’s commitment to craftsmanship. The solid construction minimizes vibrations and enhances durability, which is crucial for sustained performance over time. The user-friendly interface is designed to simplify navigation through settings and features, making it accessible for both audiophiles and casual users.

Connectivity options on the AVR100 are extensive, including multiple analog and digital inputs, allowing for a variety of source components to be connected. The receiver also supports mass storage devices and streaming services, catering to the demands of modern users who wish to access music and media easily.

Overall, the Arcam AVR100 stands out as a sophisticated AV receiver that balances powerful audio performance, versatility, and ease of use, making it an excellent choice for anyone seeking to create a premium home theater experience.
Top Page Image Contents