LG Electronics 42LT670H, 37LT670H, 32LT670H, 26LT670H setup guide Clone Programmer Cloning Procedures

Clone Programmer Cloning Procedures (Cont.)

(Optional) Set the Clock

Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the LT2002 clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The LT2002 can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute. (Another reason that the LT2002 should be equipped with fresh, high- quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the LT2002’s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port.

After the time is copied to the LT2002 clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1.Turn ON the Target TV.

The next step depends on whether the Automated Installation Routine Wizard appears on the screen when you turn ON the TV:

•If the wizard is displayed, the TV is already in the required factory default state. Use the Up/Down arrow keys on the Installer Remote to select Exit from the Welcome screen, and press OK to exit the wizard. Then, go to step 3.

•Otherwise, ensure the Target TV is in Pass-through Mode. Then, continue with step 2.

2.Use the Installer Remote to access the Target TV Installer Menu (see “Access- ing the Installer Menu” on page 18 for further information). Set Installer Menu item 117 FACT DEFAULT to 001, and press OK. When the value changes back to 0, press OK again to exit the Installer Menu.

Note: This step restores factory default settings on the TV, which will in turn re-activate the Automated Installation Routine Wizard. Use the Up/Down arrow keys on the Installer Remote to select Exit from the Welcome screen. Then, press OK to exit the wizard.

3.Tune/set the TV to an analog channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and then connect the MPI cable to the MPI port on the Target TV.

4.With “THE CLONE HAS CONTROL OF TV” message on display, press 2 on the Installer Remote to select TEACH TO TV from the LT2002 Clone Selection Menu. Then, press OK.

5.Select the LT2002 Memory Bank in which the new Master TV Setup is located, and press OK.

6.Verify the Teaching setup information on the next screen, and then press POWER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be displayed on-screen during Teaching. When the Teaching process is complete, a “TEACHING COMPLETE” message will be displayed.

7.When Teaching is done, disconnect the MPI cable from the Target TV, and turn OFF the TV.

8.After a few seconds, turn ON the TV, and verify that the Master TV Setup is now resident on the Target TV.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2)TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2) TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

COPY SELECTED CLONE MEMORY

TO TV

(1)MEMORY 1 VER XX REV XX

(2)MEMORY 2 VER XX REV XX

(3)MEMORY 3 VER XX REV XX

(4)RETURN TO CLONE MENU

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

36 206-4213