Safety 1st 4358-5721 Install Rear-Facing with, Fold the recline stand Check for Proper Recline

Page 21

E-3 Install Rear-Facing with

LATCH

1. Fold the recline stand

Note: Review your vehicle’s owner manual for LATCH belt use.

4. Check for Proper Recline

E. Installing

under the child restraint

Do not use the LATCH system along with the vehicle lap or lap/shoulder belt.

Check LATCH belt before each use. Use only if the belt can be tightened properly and securely.

Attach the top anchorage hook (tether) to recline stand when used rear-facing.

Failure to follow these warnings can result in serious injury or death.

4360-2334

 

 

 

Most Upright Level to Ground Line

 

 

Rear-Facing

 

 

For Children 22-40 lbs (10.1-18 kg)

 

 

AND can sit up unassisted

 

 

Recline range is between the 2 level to

 

 

ground lines.

 

 

Review instruction manual.

 

 

 

Line

 

 

LeveltoGround

 

 

MostReclined Facing

 

 

Rear-

5-22lbs

 

 

Childrenkg)

 

 

For (2.3-10MUSTBe

 

 

BottomLine

the

 

 

Levelwith.

Most

 

Ground

 

 

 

Upright Level to

Ground Line

 

For

Rear-

 

 

Children 22-40Facing

 

 

ReclineAND can sit up lbs (10.1-18 kg)

 

 

range is betweenunassisted

 

 

ground lines. the

2 level to

 

Most Reclined Level to Ground Line

 

 

Rear-Facing

 

 

For Children 5-22 lbs

 

 

 

(2.3-10 kg)

 

 

Bottom Line MUST Be

 

 

Level with the

 

 

 

Ground.

 

For children between

5-22 lbs (2.3-10 kg), the bottom level to ground line MUST be level to the ground.

For children 22-40 lbs (10.1-18 kg) and can sit up unassisted, rotate the child restraint between the

2 level to ground lines. Start by making the bottom level to ground line level, then rotate seat up. DO NOT rotate past the top most upright level to ground line.

Adjust child restraint if needed.

Rear-Facing

2. Store Top Anchorage Hook (Tether)

Attach the top anchorage hook (tether) to recline stand as shown. Tighten tether to remove the slack.

3. Place Child Restraint

in the Back Seat Rear-

Facing

Move the front seats forward to give you room to install the child restraint. With the child restraint in the fully reclined position, center the child restraint in the chosen seating position.

 

You may need to place a

A

large rolled towel(s) or foam

 

pool noodle(s) (A) under the

 

front of the child restraint

 

to help achieve the correct

 

recline. Check often to be

 

sure padding is still in place

 

and the LATCH belt is tight.

5.Hook LATCH to Vehicle Anchor

Fasten one LATCH belt hook to the anchor in the vehicle seat located in the vehicle seat bight. Repeat for other side of child restraint.

39

40

continued on next page.

Image 21
Contents Guide See our full line of crash tested accessories atRegistration and Safety Notices General Vehicle Installation .....PagesSafety Hotline at Registration and Safety NoticesThank You Fax1-800-207-8182 Mailing AddressBefore You Begin Understanding Your Child RestraintBack View Safety Information Installation in VehicleVehicle Seating Position Child Restraint UsePreparing Child Restraint to Fit Your Child Choose Position for Your ChildLoosen Harness Release Chest ClipPlace Child in Child Restraint Check Buckle PositionTo Change Buckle Position Forward-Facing Position Rear-Facing PositionBasic Use Securing Child in Child RestraintCheck Harness Tightness Removing Child From Child RestraintPosition Chest Clip UnbuckleAccessories Reclining Child RestraintRemoving Harness System Guides Removing Pad for CleaningWith one hand while Other hand Remove the ElasticDo not use child restraint without the pad Installing Harness SystemAttach Harness Straps to Splitter Plate Understanding Your VehicleSeat Bight Anchor Brackets Air BagsBelt at the same time Choosing Latch or Vehicle BeltsVehicle Belts For specific instructionsKnowing Your Vehicle Belts InstallationVehicle Belts Vehicle Latch PlatesUsing the Locking Clip Locate Locking Clip Location Installing on AircraftAttach Locking Clip Position Locking ClipPreparing to Install Latch Rear-Facing Preparing to Install Rear-FacingFold the recline stand Check for Proper Recline Install Rear-Facing withUnder the child restraint Place Child Restraint Back Seat Rear FacingVehicle Belts Tighten Vehicle Belt To Opposite SideThread Vehicle Belt Check Vehicle belt TightnessAdjusting Top Anchorage Strap Tether Preparing to Install Forward-FacingInstall Forward-Facing With Latch Preparing to Install Latch Forward-FacingCheck Latch Belt Tighten Top Anchorage Strap TetherInstall Forward-Facing With Vehicle Belts Child Restraint Must be UprightPlace Child Restraint Vehicle Forward-Facing Limitation of Damages WarrantyReplacement Parts Order Form Trouble ShootingPart Cost Replacement Parts List

4358-5721 specifications

The Safety 1st 4358-5721 is a highly regarded child safety seat designed to ensure the utmost protection and comfort for your little one during travels. This model has carved a niche in the market due to its impressive features and innovative technologies that prioritize child safety and convenience for parents.

One of the standout features of the Safety 1st 4358-5721 is its multi-stage design. This seat is crafted to provide a secure environment from infancy through childhood. It offers a rear-facing option for younger children, ensuring that the most vulnerable passengers travel in the safest position. As your child grows, the seat can be converted to a forward-facing mode, accommodating various weight ranges and enhancing longevity.

The installation process of this car seat is simplified with the EasyInstall technology. The seat is equipped with a simple LATCH (Lower Anchors and Tethers for Children) system, which allows for quick and secure installation, reducing the likelihood of user error and enhancing safety. This feature is particularly beneficial for busy parents who appreciate ease of use without compromising safety.

Safety features are paramount in the Safety 1st 4358-5721 design. It includes a five-point harness system that secures your child firmly while allowing for easy adjustments as they grow. Furthermore, the seat is designed with side-impact protection, which is crucial in the event of a collision, minimizing the risk to your child's head and torso.

Comfort is also a key focus of this child safety seat. The Safety 1st 4358-5721 is equipped with plush padding and a removable, machine-washable cover, making it easy to maintain cleanliness and hygiene. The seat is designed to provide ample support for long journeys, catering to the diverse needs of growing children.

In terms of safety certifications, the Safety 1st 4358-5721 adheres to rigorous safety standards set by the American National Standards Institute (ANSI) and exceeds federal crash test requirements. This level of assurance offers peace of mind to parents seeking reliable options for their children’s safety.

In conclusion, the Safety 1st 4358-5721 represents a blend of security, comfort, and convenience. With its multi-stage functionality, easy installation, robust safety features, and comfort-enhancing design, this car seat is a practical choice for families seeking to ensure safe travel for their children. It stands as a testament to Safety 1st’s commitment to innovative and reliable child safety solutions.