Pelco C540M (6/98), CM9760-KBR Diagnostics Mode, Testing the Display, Testing the Keys

Page 17

3.3 DIAGNOSTICS MODE

ADVANCE SETUP 1

> HOST SYSTEM 9750
COM 1			4800					8E
COM 2			4800					8E
COM 3			4800					8E

Diagnostics mode is activated when DIP switch 1 is ON. To leave diagnostics mode,

select and return DIP switch 1 to the OFF position. Diagnostics mode allows you to test the:

1.LCD display

2.Keys

3.Serial ports (not available at this time)

4.DIP switches

3.3.1 Testing the Display

DIAGNOSTIC MODE V3.3

LCD TEST

1.While in diagnostics mode, select .

2.Select to test Graphic Page 0.

3.Select to test Graphic Page 1.

4.Select to test Graphic Page 2.

5.Select to test the text page.

6.Select .

3.3.2 Testing the Keys

KEYBOARD TEST V3.3

PLEASE ENTER A KEY

JOYSTICK POSITION - (129,129)

NOTE: When testing the keyboard, pressing the user definable control keys causes their assigned functions to be displayed.

1.	While in diagnostics mode, select		.
2.	Press each key and check that the display indicates the correct key.
3.	Select	.

3.3.3 Testing the Serial Ports

(For factory use only)

3.3.4 Testing the DIP Switch

DIP SWITCH TEST V3.3

00000011

NOTE: When switched ON, func- tioning switches will change the cor- respondingly displayed ‘0’ to a ‘1’. For instance, when switch 2 is ON, the display should read: 00000011.

1.Select .

2.Beginning with switch 2, set each switch to ON while observing the display.

Pelco Manual C540M (6/98)

17

Image 17

Contents Esc Contents Advanced Operation Preset Camera Positions Manual # Date Comments List of IllustrationsRevision History General Important Safeguards and WarningsCertifications FCCDescription Main FeaturesModels CM9760-KBR-X Same as CM9760-KBR except 230 VAC, 50 HzLCD Display Physical LayoutMultipurpose Function Keys KeypadLens Control Function ControlSetup Installation and SetupTo Activate Setup Mode Assign functions to user-definable control keysCM9760-CC1 CM9760-KBD Basic Keyboard Setup Configuration and WiringCreating a Setup PIN To Leave Setup ModeAdjusting the Display Brightness Creating a Define PINCamera Direct Control Direct Camera Control/Serial Port SpeedsSerial Port Speeds Configuring the Relays Downloading Keyboard Setups Setting Up a Receiver/Driver Keyboard Define Mode Setup information that can be downloaded/uploaded includesDownloading Keyboard to Keyboard Setups are downloaded keyboard to keyboard byAssigning Logical Camera Numbers Downloading Through the CM9760 System Adjusting the Time-out PeriodTesting the Display Diagnostics ModeTesting the Keys Testing the Serial PortsIntroduction OperationOverview Logging onLogging OFF Using the keypad, enter a monitor number, and then press orSelecting Monitors Selecting CamerasSelecting Group Cameras Locking Cameras or Input DevicesGroup Input Selection Overriding Camera Locks Operating PTZ CamerasOverriding Camera Control Recalling Presets Preset Camera PositionsCreating Presets Deleting PresetsVCR Control VCR Recording with the Pelco Alarm Interface Unit AIUVCR Control Via the Pelco IR Controller To control VCRs, see .3 GPI controlGPI Control Type the GPI number using the keypad and then pressSelecting GPIs MacrosFinding Macros Pausing MacrosRestarting Macros Creating Temporary Macros Deleting MacrosVideo Loss Camera is disabledCamera Sequences Setting the Time and DateArming Alarms AlarmsDisarming Alarms Or selectResetting Triggered Alarms Alarm StatusResetting Alarms Appendix B. Icon Legend AppendicesAppendix A. Keyboard LCD Default Menu and Tree List Appendix B. Icon Lagend RS-232 Serial Port Appendix C. Keyboard Connector Pin-OutsRS-422 Serial Port JP4 Pin Function I2C Bus PortRelay Port JP5 PinSame Direction Appendix D. Keyboard-to-Keyboard Cabling ConnectionsOpposite Tree DIP Switch 2 on Appendix E. Setup Mode MenuDiagnostic Mode LCD Test Keyboard Test Appendix F. Diagnostic Mode Menu Tree DIP Switch 1 onDiagnostic Mode Serial Port Test Diagnostic Mode DIP Switch TestElectrical Appendix G. CM9760-KBD SpecificationsOperational GeneralReturns Warranty and Return InformationWarranty