Pelco C540M (6/98), CM9760-KBR operation manual Installation and Setup, To Activate Setup Mode

Page 9

3.0 INSTALLATION AND SETUP

3.1INSTALLATION (Refer to Figure 5 on the next page)

1.Ensure that all DIP switches are in the OFF position, as shown in Figure 3. The DIP switches are on the underside of the keyboard.

2.The RJ-45 connectors on the supplied Pelco power pack serve a dual func- tion: (1) to provide power to the keyboard and (2), serve as a data path be- tween the keyboard and the CM9760-CC1. Connect a “straight” or “parallel” cable (RJ-45 to RJ-45) between COM 1 on the keyboard and the RJ-45 key- board input connector on the power pack (refer to Figure 5).

3.Connect the other “reverse” or “cross-wired” cable (also RJ-45 to RJ-45) be- tween the remaining RJ-45 connector on the power pack and an appropriate RJ-45 Sercom port (most likely Com port 6) of the Sercom board occupying slot 1 on the rear of the Pelco CPU (CM9760-CC1).

4.Plug the power pack into a 120 VAC power source.

5.Turn the main power supply switch ON.

Figure 3. DIP Switches

 

VOLUME

 

RELAY 12C COM 3 COM 2 COM 1

RESET

DIP SWITCHES

 

BUTTON

(REFER TO APPENDIX C FOR ALL KEYBOARD CONNECTOR PIN-OUTS)

Figure 4. Com Ports and DIP Switches

3.2 SETUP

NOTE: The DIP switches are on the underside of the keyboard (see Fig- ure 4). The default setup PIN is 1234. It may be altered in setup mode. See Appendix E, Setup Mode Menu Tree.

NOTE: To restore factory default settings, set DIP switch positions 1, 2 and 8 to the ON position and re- cycle power.

The CM9760-KBD is configured using setup mode. In setup mode, it is possible to

•Nominate a PIN for entering setup mode

•Nominate a PIN that provides access to features on the define menu

•Calibrate the joystick

•Adjust the brightness of the display

•Set the data transmission speeds at which the keyboard’s three COM ports operate

•Configure the internal relays and assign macros to them

•Assign functions to user-definable control keys

•Select direct camera control receiver/drivers.

•Assign logical camera numbers to directly controlled cameras.

•Download/upload the definitions of the user-definable control keys and user defined icons between keyboards

•Adjust the time-out period

•Select a host processor

3.2.1To Activate Setup Mode

1.Set DIP switch 2 to the ON position

2.Enter your setup PIN.

Pelco Manual C540M (6/98)

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Esc Contents Advanced Operation Preset Camera Positions List of Illustrations Revision HistoryManual # Date Comments General Important Safeguards and WarningsCertifications FCC Description Main Features Models CM9760-KBR-X Same as CM9760-KBR except 230 VAC, 50 HzLCD Display Physical LayoutMultipurpose Function Keys KeypadLens Control Function ControlSetup Installation and SetupTo Activate Setup Mode Assign functions to user-definable control keysCM9760-CC1 CM9760-KBD Basic Keyboard Setup Configuration and WiringCreating a Setup PIN To Leave Setup ModeAdjusting the Display Brightness Creating a Define PINCamera Direct Control Direct Camera Control/Serial Port SpeedsSerial Port Speeds Configuring the RelaysDownloading Keyboard Setups Setting Up a Receiver/DriverKeyboard Define Mode Setup information that can be downloaded/uploaded includesSetups are downloaded keyboard to keyboard by Assigning Logical Camera NumbersDownloading Keyboard to Keyboard Downloading Through the CM9760 System Adjusting the Time-out PeriodTesting the Display Diagnostics ModeTesting the Keys Testing the Serial PortsIntroduction OperationOverview Logging onLogging OFF Using the keypad, enter a monitor number, and then press orSelecting Monitors Selecting CamerasLocking Cameras or Input Devices Group Input SelectionSelecting Group Cameras Operating PTZ Cameras Overriding Camera ControlOverriding Camera Locks Recalling Presets Preset Camera PositionsCreating Presets Deleting PresetsVCR Control VCR Recording with the Pelco Alarm Interface Unit AIUVCR Control Via the Pelco IR Controller To control VCRs, see .3 GPI controlGPI Control Type the GPI number using the keypad and then pressSelecting GPIs MacrosPausing Macros Restarting MacrosFinding Macros Creating Temporary Macros Deleting MacrosVideo Loss Camera is disabledCamera Sequences Setting the Time and DateArming Alarms AlarmsDisarming Alarms Or selectAlarm Status Resetting AlarmsResetting Triggered Alarms Appendix B. Icon Legend AppendicesAppendix A. Keyboard LCD Default Menu and Tree List Appendix B. Icon Lagend Appendix C. Keyboard Connector Pin-Outs RS-422 Serial PortRS-232 Serial Port JP4 Pin Function I2C Bus PortRelay Port JP5 PinAppendix D. Keyboard-to-Keyboard Cabling Connections OppositeSame Direction Tree DIP Switch 2 on Appendix E. Setup Mode MenuDiagnostic Mode LCD Test Keyboard Test Appendix F. Diagnostic Mode Menu Tree DIP Switch 1 onDiagnostic Mode Serial Port Test Diagnostic Mode DIP Switch TestElectrical Appendix G. CM9760-KBD SpecificationsOperational GeneralWarranty and Return Information WarrantyReturns
Top Page Image Contents