Pelco DD53CBW18-X manual Window Blanking Disabled, Window Blanking Enabled

Page 37

SPECTRA III

LANGUAGEENGLISH

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD>

BACK

EXIT

6.The blanked area can be programmed to turn on or off at a specified zoom point. To set the zoom point:

a.Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open.

b.Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point.

NOTE: Since the area is already blanked out, it may be difficult to determine when you want window blanking to turn on. Reverse the window before setting the zoom point. When finished reverse the window again to blank out the area.

Window Blanking Disabled

Window Blanking Enabled

NOTE: Increase the size of the window if any part of the blanked area is revealed during pan, tilt, and zoom operations.

WINDOW BLANKING

STYLEGRAY

BLANK ALL ABOVE	OFF
BLANK ALL BELOW	OFF
<SET WINDOW>
BACK
EXIT

SET WINDOW
WINDOW NUMBER	1
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
ENABLE WINDOW	NO
REVERSE
CLEAR WINDOW
BACK
EXIT

*This setting only applies to	Quick Programming Guide
Pressurized Spectra III dome	Quick Programming Guide
systems with software version
1.27 or higher.

(See page 11)

C2487M-B (11/05)

37

Image 37

Contents DD53CBW18 & DD53CBW18-X Spectra III SeriesPage Page Page Contents Blank ALL ABOVE/BLANK ALL below Welcome Configure DoneGetting Started Pelco Spectra Version Address Comm 2400, N, 8HOW to Operate Your Dome System CM6700/CM6800 Accessing Main Menu PresetNET300/NET350/NET4001A Preset Function Following presets are reserved for special functionsPage Quick Programming Guide LanguageSee System Information Display Setup Label Position Camera Dome SettingsAuto Focus Button on the controllerZoom Speed Zoom LimitLOW Light Limit HighAuto IR Level IR CUT FilterDark Shutter Speed Advanced Camera SettingsAGC Limit Numeric ValueAuto Iris Level Auto IrisAuto Iris Peak Auto White Balance Auto SharpnessGain OFF default There are two backlight compensation settingsBacklight Compensation BLC Set the video output to one of the following Video LevelNormal Volt peak-to-peakAuto Flip Motion SettingsProportional PAN There are two auto flip modesPreset None default No actionPark Time Park ActionScan Speed Preset Freeze FrameManual Limit StopsScan Limit stop is reachedAzimuth Zero Power UP Action Power UpLine Sync Phase settings range from 0-359 degreesDome synchronizes to an internal clock Following presets are predefined for specific functions PresetsPreset Action Determined zero reference pointQuick Programming Guide Patterns Zones Move the cursor beside Zone Enabled or Zone BlankingTo edit a zone label Press Iris Open. The cursor moves to the rightTo set the window blanking area Window BlankingWindow Blanking Enabled Window Blanking DisabledClear Window ReverseBlank ALL ABOVE/BLANK ALL below Blank All AbovePress Iris Open to enter selection AlarmsLatching AuxMomentary Title Text Repeat AlertSystem Condition Alert Message ACK Action Reset AlertCurrent Reading Clear Password Reset Camera RESET, Cycle POWER, RebootCycle Camera Power Reboot SystemUpload Icon SOFTWARE/LANGUAGE File UploadUpload Icon DD53CBW18 SpecificationsDD53CBW18-X NtscRadio and Television Interference Regulatory NoticesPage Page ISO9001