Hitachi HV-D30 operation manual Dtl, Low, Standard, High

Page 38



11. DTL

Menu for setting detail parameters

1) DTL FREQ : DTL amplifying frequency changeover.

LOW

: The lower band frequency is amplified.

STANDARD

: The standard amplification is performed.

HIGH

: The high band frequency is amplified. Finer contour correction is

 

carried out.





2) Hi chroma DTL : High chroma detail on/off

At on setting, contours are enhanced in highly colored components of the scene.

3) Color DTL : Selects color detail mode

CH1, CH2 : Either selection engages color detail. Sets the detail level of two color

 

phase ranges. Select each color phase setting with CH1 and CH2.

Off

: Color detail is disengaged.

4)Auto setup : Color detail phase is detected automatically. Set the marker to the desired phase area and press R for automatic detection (indicates OK when completed).

5)Level : Sets color detail level

Range is -128 (soft) to 127 (sharp). Press both L and R for about 2 seconds to set to 0.

6) Phase : Sets color detail phase

Present phase is indicated beside the setting values. Since the VBS output is shown as monochrome on the monitor, a monochrome indication can also be used for an approximate setting. At Auto setup, the automatically detected phase setting is indicated.

Note: At RGB or R-Y, B-Y output, the detected phase range is not shown on the monitor. Use a VBS signal for color detail setting.

7) Width : Selects color phase range for setting

Setting range is -128 (narrow) to 127 (wide). Since the VBS output is shown as monochrome on the monitor, a monochrome indication can also be used for an approximate setting. Press both L and R for about 2 seconds to set to 0.

Note : At RGB or R-Y, B-Y output, the detected phase range is not shown on the monitor.Use a VBS signal for color detail setting.

25

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Model HV-D30 Read Instructions CleaningAccessories Retain InstructionsGrounding or Polarization Power SourcesPower-Cord Protection LightningSafety Check Damage Requiring ServiceReplacement Parts Wall or Ceiling MountingWarnungen beachten Alle Anweisungen lesenDie Anweisungen aufbewahren Anweisungen befolgenNetzkabelschutz StromversorgungErdung oder Polarisierung BlitzschlagBeschädigung, die Wartung erfordert Starke stöße oder VibrationenWartung ErsatzteileConserver ces instructions AccessoiresLire les instructions Tenir compte des avertissementsProtection du cordon d’alimentation Sources d’allmentationMise á la terre ou polarisation FoudreDommages nécessitant réparations Chocs ou vibrations violents19. Réparations 21. Piéces de rechangeImportant Notice Table of contents Page Overview FeaturesStandard composition Page CCD properties Continuous operationTransportation Page FILE/R button Menu ModeName and function each section Pilot lampLens Lens selectionVideo signal type lens adjustment Triangle mark is center. If Camera mounting System examples Menu Screen Operation Menu StructureSpecial SET Lens Hite Gate Main Menu SUB Menu Auto electronic shutter operates in the Limit range setting Comb Filter Slow Auto ShadingALC FastALC Gate ON/OFF toggle Special SET Lens White Gate Level Masking Gamma Standard DTLLOW HIGHDTL SUB Mode MODE1, CCD Mode FLD Ext triggerMode MODE2, CCD Mode FRM Mode MODE1, CCD Mode FRMMode MODE2, CCD Mode FLD OUTPUT/SYNC File set Other FuncID/TITLE Display Position 17. ID/TITLETitle Auto Black BAR How to Attain Better ImagesBlack Balance Adjustment Auto BlackWhite Balance Adjustment Change to Manual Long Shutter Mode Change TRY Again CAM Mode AutoTemp LOW Realtime Auto White Auto Shading CorrectionALC 38 RC-Z3 Remote Control Panel OperationRC-Z3 panel facilities   Extender LEDPage Gain control MEM AUTOMenu screen composition SW401 Function Selection by Internal Switch SettingSW806 Connectors  GND CCD SpecificationsNTSC, PAL Ntsc50.31 to 1/2024 second H Output signal ratings Input/Output SignalsInput signal conditions Page Major accessories Dimensions
Top Page Image Contents