Hitachi HV-D30 operation manual Output/Sync

Page 42

14. OUTPUT/SYNC

On this menu screen, you can make signal changeover for output to the D-SUB connector and phase adjustment for external synchronization.

1) OUTPUT : Output mode changeover

R, G, B The R, G and B video signals are output to the D-SUB connector.

Y, R-Y, B-Y The Y, R-Y and B-Y signals are output to the D-SUB connector. Y/C The Y/C and VBS signal is output to the D-SUB connector.

2)COLOR BAR : Color bars ON/OFF

3)MONO : Monochrome (black and white) ON/OFF for the video output signal from the VIDEO connector

Set to ON for monochrome. Setting ineffective during color bar.

4)Sync/HD out : Selects sync signal output from the rear panel multi connector.

5)SYNC ON G : G video signal synchronization ON/OFF (In the R/G/B mode only) When output is RGB with Sync on and G on, Sync is added to the G video signal.

6)GL IN : Impedance changeover of input to the GL IN connector.

HIGH : The high impedance level is provided.

75 : An impedance of 75 ohms is provided.

Note: When power to the camera is turned off, the high impedance level is provided. So, do not use this function in a system where power is turned off for the camera unit only.

7) GL MODE : GL signal input changeover

VBS : The VBS signal or BBS (black burst) signal is input as an external synchronizing signal.

HD/VD : The HD/VD signal is input as an external synchronizing signal.

Note: During external sync with HD and VD signals, be sure to use either RGB or Y, B-Y, R-Y output signals. Although VBS and Y/C output signals are also produced, these cannot be used as normal output signals.

8) SC.COARSE : Coarse adjustment of subcarrier phase

Using the L or R button, select one of the following phases; 0º, 90º, 180º and 270º.

29

Image 42

Contents Model HV-D30 Read Instructions CleaningAccessories Retain InstructionsGrounding or Polarization Power SourcesPower-Cord Protection LightningSafety Check Damage Requiring ServiceReplacement Parts Wall or Ceiling MountingWarnungen beachten Alle Anweisungen lesenDie Anweisungen aufbewahren Anweisungen befolgenNetzkabelschutz StromversorgungErdung oder Polarisierung BlitzschlagBeschädigung, die Wartung erfordert Starke stöße oder VibrationenWartung ErsatzteileConserver ces instructions AccessoiresLire les instructions Tenir compte des avertissementsProtection du cordon d’alimentation Sources d’allmentationMise á la terre ou polarisation FoudreDommages nécessitant réparations Chocs ou vibrations violents19. Réparations 21. Piéces de rechangeImportant Notice Table of contents Page Features Standard compositionOverview Page Continuous operation TransportationCCD properties Page FILE/R button Menu ModeName and function each section Pilot lampLens Lens selectionVideo signal type lens adjustment Triangle mark is center. If Camera mounting System examples Menu Screen Operation Menu StructureSpecial SET Lens Hite Gate Main Menu SUB Menu Auto electronic shutter operates in the Limit range setting Comb Filter Slow Auto ShadingALC FastALC Gate ON/OFF toggle Special SET Lens White Gate Level Masking Gamma Standard DTLLOW HIGHDTL SUB Mode MODE1, CCD Mode FLD Ext triggerMode MODE1, CCD Mode FRM Mode MODE2, CCD Mode FLDMode MODE2, CCD Mode FRM OUTPUT/SYNC File set Other FuncID/TITLE Display Position 17. ID/TITLETitle Auto Black BAR How to Attain Better ImagesBlack Balance Adjustment Auto BlackWhite Balance Adjustment Long Shutter Mode Change TRY Again CAM Mode Auto Temp LOWChange to Manual Realtime Auto White Auto Shading CorrectionALC 38 RC-Z3 Remote Control Panel OperationRC-Z3 panel facilities Extender LEDPage Gain control MEM AUTOMenu screen composition Function Selection by Internal Switch Setting SW806SW401 Connectors GND CCD SpecificationsNTSC, PAL Ntsc50.31 to 1/2024 second H Input/Output Signals Input signal conditionsOutput signal ratings Page Major accessories Dimensions