EverFocus EZ630 manual Installation, Chapter, Wiring and Mounting

Page 13

Chapter

Chapter

2

2 INSTALLATION

This chapter will describe, in general terms, how to install the EZ610/630 camera.

STEPS:

1.Wire and mount the camera. See 2.1

2.Adjust the camera position. See 2.2

Warning

To prevent electrical shock, turn off the electrical power before making electrical connections.

2.1 Wiring and Mounting

Use the template and an appropriate tool to drill 4 holes to attach the speedy-mount ring. If no surface wire will be used, please insert the provided plug into the ring from the underside; the plug will be held securely in place by the ring. If surface wire access is required, simply omit the plug to leave the surface wire channel clear.

Push the plastic anchors into the 4 holes.

3.Take a long Phillips pan head screw and tighten it through the EZ Mount Ring counter-bored hole into a plastic anchor. Repeat this step until all 4 screws are secured to the wall/ceiling.

4.Drill a 1” diameter hole within the interior of the EZ Mount Ring.

5.Pull the cables to be connected to power & video cables from the ceiling or wall.

13

Image 13

Contents Low Light IR Inline IP66 Bullet Camera Low Light Inline IP66 Bullet CameraInstallation / Operation Instructions EZ610P/N 4605XZ0610004AR Operation InstructionPrecautions Reorient or relocate the receiving antenna Federal Communication Commission Interference StatementIncrease the separation between the equipment and receiver Consult the dealer or an experienced radio/TV technician for helpTable of Contents 4.1.2 OSD Menu Setting by Keyboard RS - 485 Wiring4.1.3 Lens Adjustment by Keyboard RS-485 Wiring1 PRODUCT OVERVIEW 1.1 FeaturesChapter 1.2 Accessory Parts List 1/601/50 ~1/100,000 1.3 Specifications0.45 Split glass isolation prevents internal reflectionsWeight 1.4 Dimensions1250 g / 2.275 lbs Mounting PatternSpeedy-mount Ring 1.5 Camera Component DescriptionRed Menu mode Green Lens mode EverFocus control keyboard EKB500 1.6 Related ProductsAny EverFocus DVR with RS-485 interface for PTZ control 2.1 Wiring and Mounting 2 INSTALLATIONChapter Power Socket Video & Power cables RS485 cable optional White RS-485 + Black RS-485Power and Video connection Power RS-4851st axis Use a hexagon key to loosen this screw to rotate the camera 2.2 Adjust Camera Position2nd axis Use a hexagon key to loosen this screw to rotate the camera Loosen this screw 3rd axis Loosen lock ring and set screw to rotate camera SunshieldPage 3.1 Control Key General Operation Guide 3 OSD MENU SETUP3.2 RS485 ID & Baud Rate Setting 3.3.1 OSD Menu Tree 3.3 OSD Menu Setup3.3.2 LENS 3.3.3 EXPOSURE TOP/BOTTOM 3.3.3.5 D-WDR 3.3.4 WHITE BALANCE CONTROLAuto Tracking White Balance This mode can be used within the color 3.3.5 DAY NIGHT 3DNR 3.3.63.3.7 SPECIAL the light sensor at the front of the camera body. default for EZ630image 3.3.7.3 FREEZEprevious menu. Press “END” to save all the menu settings and exit Press “RET” to save all settings in MOTION menu and return to theprevious menu. Press “END” to save all the menu settings and exit 3.3.8 ADJUST3.3.9 RESET Remote control with EKB-500 keyboard RS-485 REMOTE CONTROL4.1.1 RS - 485 Wiring 4.1.2 OSD Menu Setting by Keyboard4.1.3 Lens Adjustment by Keyboard 4.2 Remote Control with EverFocus DVR4.2.1 RS-485 Wiring 4.2.2 Camera Operation and Setup by DVREverFocus Electronics Corp