Philips BB-HCA10CE manual Specifications, Operating +0 C to +40 C, Weight About 900 g

Page 5

9.Attach the connector cover (included) and connect the necessary cables to the camera.

Align the “ ” of the connector cover with the center of the recessed area of the bracket.

Cut spaces in the connector cover to make room for the cables that will be connected to the camera. Cut along the perforated lines.

Recessed area

10.Attach the camera to the bracket in 3 places using screw B (included).

Align the arrows on the ceiling plate (included with the camera) and the bracket when attaching the camera.

Ceiling plate arrow

Camera direction

 

11.Secure the ceiling mounting cover (included) to the bracket.

1Pass the safety wire through the ceiling mounting cover as shown.

2Align the “ ” marks on the rear of the camera and on the ceiling mounting cover.

3Turn the ceiling mounting cover clockwise until the “ ” mark on the rear of the camera and the “” mark on the ceiling mounting cover are aligned as shown.

Be careful not to nip the cables, cords, etc.

To remove the ceiling mounting cover, turn it counterclockwise until the “ ” mark on the rear of the camera and on the ceiling mounting cover are aligned, then lower the ceiling mounting cover.

12.Secure the safety wire to the ceiling.

Secure the bracket’s safety wire first, using screw A and the washer (included with the bracket), then secure the camera’s safety wire, using screw A and washer A (both included with the camera).

Secure the safety wires to the ceiling about 160 mm from the center of the camera.

Do not drive the screws into a soft material. Drive the screws into a secure, 25 mm thick area of the ceiling, such as a crossbeam, otherwise the bracket and the camera may fall. If there is no crossbeam, place a board on the other side of the ceiling to make sure the bracket and the camera are securely mounted.

Washer

Washer A

(Inside diameter:

(Inside diameter: 4.0 mm)

4.0 mm)

Screw A

Screw A

(Length: 20 mm,

(Length: 20 mm,

Body diameter: 4.0 mm)

Body diameter: 4.0 mm)

Specifications

Operating

+0 °C to +40 °C

temperature

 

 

 

Dimension

About 270 mm × 77.5 mm × 270 mm

(W×H×D)

 

 

 

Weight

About 900 g

 

 

English

5

Image 5
Contents PQQX16478ZA KK0208CM0 CE Ceiling Flush Mount Bracket Indoor Use Only Installation GuideAbbreviations PreparationCeiling board must be no more than 40 mm thick Important Information Regarding Camera MountingMounting the Bracket and the Camera Secure the safety wire to the bracket using screw B includedOperating +0 C to +40 C SpecificationsWeight About 900 g Applique de montage au plafond encastré Utilisation à Guide d’installationAbréviations PréparationMise en garde Informations importantes concernant le montage de la caméraMontage de l’applique et de la caméra Fixez le fil de sécurité au plafond Caractéristiques techniques+0 C à +40 C Environ 900 gAbkürzungen InstallationsanleitungVorbereitung Modellnr. BB-HCA10CEHinweis Wichtige Informationen zur KameramontageVorsicht Montage von Halterung und Kamera Befestigen Sie den Sicherheitsdraht an der Decke SpezifikationenZwischen +0 C und +40 C Ca gPreparazione Guida di installazioneAbbreviazioni Nota AttenzioneInserire la staffa nel foro sul soffitto Montaggio della staffa e della videocameraFare attenzione a non pizzicare i cavi, ecc SpecificheFissare il cavo di sicurezza al soffitto Temperatura di Da +0 C a +40 C esercizioPreparación Guía de instalaciónAbreviaturas Precaución Información importante relativa al montaje de la cámaraMontaje del soporte y de la cámara Asegúrese de no retorcer los cables, hilos, etc EspecificacionesFije el cable de seguridad al techo Temperatura de +0 C a +40 C funcionamientoМодели BB-HCA10CE Руководство по установкеСокращения ПодготовкаВнимание Важная информация относительно установки камерыПримечание Используйте винты, соответствующие материалу потолкаКамерой Монтаж кронштейна и камерыЗажимы затягиваются по мере затяжки винтов 12. Прикрепите контровочную проволоку к потолку Технические характеристикиРабочая От +0C до +40C Мм mm ×部件号 XWG4F16VW 部件号 PNPD1087Z 型号 BB-HCA10CE部件号 PQKL10092Z1 部件号 XTB4+20AFJ 部件号 XYN4+F6FJ 部件号 PQME10080Z 部件号 PNHX1058Z有关摄像机安装的重要信息 安装支架和摄像机 +0 C 至 +40 C 주문 번호 XWG4F16VW 주문 번호 PNPD1087Z 모델 번호 BB-HCA10CE주문 번호 PQKL10092Z1 주문 번호 XTB4+20AFJ 주문 번호 XYN4+F6FJ 주문 번호 PQME10080Z 주문 번호 PNHX1058Z 문서1 권천장에 받침대와 카메라를 장착할 때 안전 와이어를 연결하여 받침대와 카메라가 떨어지지 않도록 하십시 카메라를 장착하기 전에 다음 정보를 자세히 읽어보십시오. 장착에 대해서는 지정 대리점에 문의하십시오받침대 및 카메라 장착 작동 온도 +0 C ~ +40 C 크기W×H×D 270mm × 77.5mm × 270mm 900g Page