Yamaha RX-V1500 owner manual Specifications

Page 100

SPECIFICATIONS

AUDIO SECTION

•Minimum RMS Output Power for Front, Center, Surround, Surround back

20 Hz to 20 kHz, 0.04% THD, 8 Ω

120 W

•Maximum Power (EIAJ)

[Australia, China, Korea, Asia and General models]

1 kHz, 10% THD, 8 Ω

170 W

•Dynamic Power (IHF)

[U.S.A., Canada, China, Australia, Asia, Korea and General models]

8/6/4/2 Ω

155/195/250/330 W

• DIN Standard Output Power [U.K. and Europe models]

1 kHz, 0.7% THD, 4 Ω

170 W

• IEC Output Power [U.K. and Europe models]

 

1 kHz, 0.04% THD, 8 Ω

125 W

• Damping Factor (IHF)

 

 

20 Hz to 20 kHz, 8 Ω

140 or more

• Frequency Response

 

 

CD to Front L/R

10 Hz to 100 kHz, –3 dB

• Total Harmonic Distortion

 

 

PHONO to REC OUT (20 Hz to 20 kHz, 1 V)

0.02%

CD, etc. to Front L/R (20 Hz to 20 kHz, 60 W, 8 Ω)

........... 0.04%

• Signal to Noise Ratio (IHF-A Network)

 

 

PHONO (5 mV) to Front L/R

 

 

[U.K., Europe and Australia models]

81 dB

[Other models]

86 dB

CD (250 mV) to Front L/R, Effect Off

100 dB

• Residual Noise (IHF-A Network)

 

 

Front L/R

150 µV or less

• Channel Separation (1 kHz/10 kHz)

 

 

PHONO (terminated) to Front L/R

60 dB/55 dB

CD (5.1 kΩ terminated) to Front L/R

60 dB/45 dB

• Tone Control (Front L/R)

 

 

BASS Boost/Cut

±6 dB/50 Hz

BASS Turnover Frequency

350 Hz

TREBLE Boost/Cut

±6 dB/20 kHz

TREBLE Turnover Frequency

3.5 kHz

• Phones Output

150 mV/100 Ω

• Input Sensitivity/Input Impedance

 

3.5 mV/47 kΩ

PHONO

CD, etc

200 mV/47 kΩ

MULTI CH INPUT

200 mV/47 kΩ

• Output Level/Output..............................................................Impedance

200 mV/1.2 kΩ

REC OUT

PRE OUT

1.0 V/500 Ω

SUBWOOFER

2.0 V/500 Ω

ZONE 2 OUTPUT

 

 

[U.S.A., Canada, U.K.,............................................Europe

1.0 V/1.2 kΩ

and Australia models]

 

ZONE 3 OUTPUT

 

 

[U.S.A., Canada, U.K.,............................................Europe

1.0 V/1.2 kΩ

and Australia models]

 

VIDEO SECTION

• Video Signal Type

PAL/NTSC

• Signal to Noise Ratio

60 dB

• Frequency Response (MONITOR OUT)

 

Composite, S-video

5 Hz to 10 MHz, –3 dB

Component

5 Hz to 60 MHz, –3 dB

FM SECTION

• Tuning Range

 

[U.S.A. and Canada models]

.......................... 87.5 to 107.9 MHz

[Asia and General models]

87.5/87.50 to 108.0/108.00 MHz

[Other models]

87.50 to 108.00 MHz

• Usable Sensitivity (IHF)

1.0 µV (11.2 dBf)

• Signal to Noise Ratio (IHF)

 

Mono/Stereo

76 dB/70 dB

• Harmonic Distortion (1 kHz)

 

Mono/Stereo

0.2%/0.3%

• Stereo Separation (1 kHz)

42 dB

• Frequency Response

20 Hz to 15 kHz, +0.5, –2 dB

AM SECTION

• Tuning Range

 

[U.S.A. and Canada models]

.............................. 530 to 1710 kHz

[Asia and General models]

530/531 to 1710/1611 kHz

[Other models]

531 to 1611 kHz

• Usable Sensitivity

300 µV/m

GENERAL

• Power Supply

 

 

 

[U.S.A. and Canada models]

.............................

AC 120 V, 60 Hz

[Australia model]

 

AC 240 V, 50 Hz

[China model]

 

AC 220 V, 50 Hz

[Korea model]

 

AC 220 V, 60 Hz

[U.K. and Europe models]

 

AC 230 V, 50 Hz

[General model]

AC 110/120/220/230-240 V, 50/60 Hz

[Asia model]

AC 220/230-240 V, 50/60 Hz

• Power Consumption

 

 

 

[U.S.A. and Canada models]

.................................

500 W/630 VA

[Other models]

 

500 W

• Standby Power Consumption

 

 

 

[Asia and General models] (AC 240 V/50 Hz)

0.8 W or less

[Other models]

 

0.5 W or less

• AC Outlets

 

 

 

[U.S.A. and Canada models]

..... 2 (Total 100 W/0.8 A maximum)

[U.K. and Australia models]

............... 1 (Total 100 W maximum)

[China and Europe models]

................

2 (Total 100 W maximum)

[Asia and General models]

2 (Total 50 W maximum)

• Dimensions (W x H x D)

435 x 171 x 433.5 mm

 

 

(17-1/8” x 6-3/4” x 17-1/16”)

• Weight

 

15.5 kg (34.2 lbs)

98

Page 99 Page 100
Image 100
Page 99 Page 100
Contents RX-V1500 For U.K. customers Special Instructions for U.K. ModelContents Features Built-in 7-channel power amplifierSound field features Other featuresInstalling batteries in the remote control Supplied accessoriesGetting Started Controls and Functions Front panelEurope models only Opening and closing the front panel DoorRemote control AMP/SOURCE/TV MuteSET Menu NightHandling the remote control Using the remote controlApproximately 6 m 20 ft Front panel display 96/24 indicator LFE indicatorInput channel indicators Presence and surround back speaker indicatorsAC Outlets Rear panelVoltage Selector Speaker Setup Speaker placementDi-pole speaker layout Speaker connections10 mm 3/8 Connecting to PRESENCE/ZONE 2 or Presence speaker terminals Tighten the knob to secure the wireBanana plug connections Speaker terminal wrench Red positive + Black negativeSUB Woofer Front terminals Center terminalsSurround terminals Subwoofer jackConnections Cable indicationsAnalog jacks Digital jacksConnecting video components Connections for DVD playbackDVD player A. model Video MonitorFor 6-channel input Connecting to the Multi CH Input jacksMulti-format player External decoder Connections for other video components Video AUX jacks on the front panelUse these jacks to connect any video source, such as Game console or camcorder, to this unitConnecting a turntable Connecting audio componentsConnections for audio components Connecting to an external amplifier Connecting the antennas Connecting the AM loop antennaFrequency Step switch Asia and General models only 75-ohm/300-ohm antenna adapter U.K. model onlyConnecting the power supply cord Other modelsAsia and General models only Memory back-upSpeaker impedance setting Turning on the powerPress STANDBY/ON to exit the setting SP IMP . SETOptimizer microphone setup Auto SetupIntroduction Automenu Starting the setupSET Menu If you selected Auto in step If you selected Step in stepIf you selected Reload in step Press n to select Start Push i, then press hBefore auto setup Troubleshooting for auto setup procedureDuring auto setup After auto setup 1OUT of Phase3LEVEL Error 4SWFR PhaseBasic Setup Using Basic MenuBasic Menu 1/2 Press n to select SWFR, then press l / h to selectBasic Menu 2/2 Bspeaker LevelPress n to select Check OK?, then press l / h to select Memory back-upAdjust the volume to the desired output level PlaybackBasic operations Select the input sourceRotate Program to select the desired program Front panel operationProgram name Remote control operation To adjust the toneTo listen with headphones Additional operationsSelecting the Multi CH Input Enjoying multi-channel software 7.1 channel surroundAuto Auto Decoders select with l / hPress Standard on the remote control to select the decoder To cancel, press Pure Direct againEnjoying 2-channel software in surround Listening to high fidelity stereo sound With Pure DirectThis adjusts the level of compression Listening to high fidelity stereo sound With Direct StereoNight listening modes Front panel display automatically dimsListening to unprocessed input signals Downmixing to 2 channelsVirtual Cinema DSP Playing video sources BackgroundSelecting input modes Displaying information about the input SourceDTS AnalogTuning Automatic and manual tuningAutomatic tuning Manual tuningPresetting stations Automatically presetting FM stationsAutomatic preset tuning options Press FM/AM to select the FM bandManually presetting stations Tune into a stationPress Memory MAN’L/AUTO FM Repeat steps 1 through 5 to store other stationsSelecting preset stations Exchanging preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit againReceiving RDS stations Changing the RDS mode Press PTY Seek Mode to set this unit in the PTY Seek mode To exit from the PTY Seek mode, press PTY Seek Mode againPTY Seek function Selected program type appears on the front panel displayTo cancel this function EON functionSpecial considerations when recording DTS software RecordingSound Field Program Descriptions For movie/video sourcesDolby Digital SUR. Standard Dolby DigitalSUR. Enhanced SUR. StandardPRO Logic SUR. Standard PRO LogicFor music sources Concert HallJazz Club Rock ConcertSetting the sleep timer Selecting the OSD mode Using the sleep timerAdvanced Operations Press l / h to adjust the speaker output level Canceling the sleep timerControl range is from +10 dB to -10 dB Using the test tone Set AMP/SOURCE/TV to AMP Press TestSET Menu Basic MenuSound Menu Input MenuUsing SET Menu Option MenuUsing Sound Menu Sound Menu 1/3Center SP Front SPSurr B L/R SP LFE/BASS OUTSurround left/right speakers Surr L/R SP Presence speakers Surround back speakers Surr B L/R SPCSP Distance Cross OverSpeaker distance CSP Distance Graphic EQ Dgraphic EQElfe Level Fdynamic RangeGlow FRQ.TEST HHP Tone CtrlIaudio SET Low frequency test Glow FRQ. TestUsing Input Menu Input MenuCMPNT-V Input Optical OUTBinput Mode OpticalCinput Rename CoaxialUsing Option Menu Dmulti CH InputOption MENU1/2 Adisplay SETSpeaker impedance setting Bmemory GuardCPARAM. INI DSP IMP.SETEzone SET FZONE2 SETGZONE3 SET Zone 2 set FZONE2 SETRemote Control Features Control areaControlling this unit Controlling other componentsSetting remote control codes Remote Control Code Default SettingsControlling optional components Optn area Set AMP/SOURCE/TV to SourcePress Learn again to exit from the setup mode Press EnterPress Enter to set the number FunctionPress an input selector button to select a source component To 10 cm 2 to 4Press Learn again to exit the learning mode Press Learn using a ballpoint pen or similar objectLearn appears in the display window Changing source names Display windowPress a macro button Using the Macro featureMacro buttons First Second Third Press Macro using a ballpoint pen or similar object Macro operationsProgramming macro operations Set Macro ON/OFF to on Press a macro buttonPress Clear by using a ballpoint pen or similar object Press k / n to select the clear modeClearing function sets Clear appears in the display windowClearing individual functions Press Clear to exit from the clearing modeClearing a learned function Press Clear to exit the clearing mode Clearing a macro functionPress Learn again to exit Press Macro again to exitControlling each component VCRSystem configuration and connection example Using external amplifiersZone 2/ZONE Zone 2/Zone 3 connectionsTo enable Zone mode on the remote Control Using this unit’s internal amplifierPress Learn to complete the Zone setup To control Zone 2/ZonePress Select k/n to exit from the Zone Zone 3 mode Turning this unit to either on or standbySpecial considerations for DTS software For DVDs encoded with DTSWhat is a sound field? Changing parameter settingsEditing Sound Field Parameters Elements of a sound fieldResetting parameters to the factory values To reset a certain parameterTo reset all parameters Press k / n to select ParametersSound Field Parameter Descriptions INIT. DLY/P. INIT. DLY Initial delayRoom SIZE/P. Room Size Room size INIT. DLY Surround initial delay SB INI. DLY Surround back initial delayRoom Size Surround room size Liveness Surround livenessREV.TIME Reverberation time REV.DELAY Reverberation delayREV. Level Reverberation level DIALG.LIFT Dialog lift For 7ch StereoFor DTS Neo6 Music Image Center image For THX Cinema DEC 2ch Decoder SelectTroubleshooting GeneralSound suddenly Goes offOnly the speaker on One side can beOr DTS indicator Volume level isRecord Volume level Dolby Digital or DTSTuner Remote control Does not work norFunction properly Does not learn newGlossary Audio formatsSound field programs PCM Linear PCMAudio information LFE 0.1 channelSampling frequency and number Quantized bits THX Cinema processingVideo signal information Specifications
Top Page Image Contents