Toshiba IK-WR01A operation manual Connecting Connect a LAN cable and then turn the power on

Page 23

Connecting

Connect a LAN cable and then turn the power on.

Connect the LAN cable (straight) leading to the camera with a powered hub. Alternatively, use a LAN cable (crossover) to connect the camera with the powered personal computer.

●When connecting a PoE compatible hub/router, power will be provided to the camera through the LAN cable even though the power plug terminal is not connected.

●When not using a PoE compatible hub, connect AC24V or DC12V power plug with the power plug terminal.

Set the IP address of the personal computer.

●Set the IP address of the computer to a setting different that 192.168.0.30 (camera’s IP address).

•Set the IP address to 192.168.0.50 (and subnet mask to 255.255.255.0) as an example.

•For details on the procedure, refer to the user’s guide of the personal computer.

Make sure whether the camera receives a reply from the personal computer.

●Start a command prompt and then run “ping 192.168.0.30.”

●If the “Reply from…” message appears, the connection is correctly established.

Installation/Set up

and OperationViewing

Recording

Search for the network camera with the “Camera Finder” (➝ page. 24) and then view camera images.

a)Start “Camera Finder” and click the “Search” button.

•Confirm that the camera name “wrcam01” and the IP address “192.168.0.30” are displayed in the camera list.

b)Click camera name, “wrcam01”, to select.

•Check that the camera name, the IP address and the HTTP port number are displayed in the login field of the network camera.

c)Click the “User” button.

•When the “User authorization” is set to “ON” (➝ page.29), a screen appears, asking you to enter the user name and the password. Enter the Administrator login ID and password or the registered user name and password.

d)The Camera Window screen appears.

NOTE

● To view the screen without using the “Camera Finder,” start the Internet browser, enter the URL “http://192.168.0.30/” and then press ENTER. When you enter a port number other than 80, specify the port number after “:” (e.g. http://192.168.0.30:88/).

● The camera takes about 30 seconds to start after the power is turned on.

23

Setting up

Others

Image 23

Contents Model IK-WR01A Important Safety Instructions Introduction Viewing and Operation IntroductionMonitor Out Connector Names and Features of PartsMode Setting Switch Lens Iris ADJ Line Lock Phase ADJEthernet Port Video Out JackInstallation/Setup Adjust the Angle of View InstallationTilt rotation Installation Recording Setting up Installing the Camera Unit46 mm Change of Dome Cover Dome replacementConnecting to a Video Monitor Connecting to a Video MonitorWhen power is supplied from a PoE compatible hub, etc About the Power Select SwitchWhen power is supplied from an AC24V or DC12V power source Line-Lock control Video Switcher CAMERA1Line Lock Phase Back Light Compensation Adjusting a LensMode Setting Switch Auto White Balance AWB Requirements for Network Camera Monitoring System Setting Up the Network Camera EnvironmentEntering an IP Address Manually About the IP AddressObtaining an IP address automatically from the Dhcp server Structure of Connection Set the IP address of the personal computer Connecting Connect a LAN cable and then turn the power onUsing Camera Finder to Search for a Camera Click the camera you want to login from the list of camerasSetting up Camera Finder Click Exit button to close Camera Finder Click the User buttonClick Admin on the left side of the screen Changing Administrator Login ID and PasswordClick the browser Click the Change buttonClick User on the left side of the screen Setting up Access RestrictionClick the Set/Change button Click Network on the left side of the screen Configuring the Network ManuallyClick the Save button Select ManuallyInstallation/Set up Viewing and Operation Close the browser to log off disconnect the camera ViewingViewing Images Camera Window Screen Menu that is displayed when right-clicking on the imageAdjusting Images on the Camera OperationViewing Adding Images Click View log on the left side of the Camera Window screen Viewing LogsOperationViewing Recording About Recording Images Recordable Media Recordable ContentsClick FTP client on the left side of the screen Recording Images on FTP ServerFTP General Settings Configure each setting itemsConnection to FTP Enable Click the Save Settings button below the settingPeriodic FTP by Schedule Configure recording scheduleEnter File Name FTP by Motion Detection Configure settings for viewing FTP status File Transfer Order Click Image Recording Setting up RecordingClick the Start button Recording Images on a Personal ComputerSpecify the destination folder and file name Click Save Current Picture AsRecording Setting up Configure each item How to Set upChanging the camera name System SettingsClick System on the left side of the screen Adjusting the date and time Setting up a format to display date/timeSetting the color of date/time display Changing the time using an NTP server settingUpdating the Firmware Rebooting the network cameraClick Export current configurations Importing the Settings Saved on a Personal ComputerDisplaying the screen asking a user name and password User SettingsDeleting a user name Storing the user name and passwordAdmin Settings Restarting the camera Changing the Administrator ID and passwordClick Alarm on the left side of the screen Alarm SettingsSetting the motion detection Setting the motion detectionConfiguring the connection Network SettingsFramerate Control Configuring the Http port numberDNS update to DNS 1/2 Server Click Mail on the left side of the screen Mail SettingsConfigure each item For details, refer to Recording Images on FTP Server → FTP Client SettingsClick Ddns on the left side of the screen Ddns SettingsBefore Starting Updating the FirmwareClick Upload button on the screen shown in Step Click Firmware updateClick the Browse button Specify the destination and then save the file Click Export current configurationsClick Import on the screen shown in Step Select the file on settings you savedSetting up Others Index Glossary Safety Precautions3Jpeg Up and OperationViewing Display of Logs Recording Setting up Before Calling Service Personnel Guide of your broadband router Before Calling Service Personnel...Symptom Cause How to Manage Cannot perform Lost the power RAM Sometimes primary is described as master Symptom Cause How to Manage Recorded Others IK-WR01A SpecificationsAppearance Diagram 150 Mounting Base BracketToshiba America Information SYSTEMS. INC

Related manuals

Manual 4 pages 31.62 Kb