Toshiba IK-WR01A operation manual Before Calling Service Personnel

Page 83

Before Calling Service Personnel...

Symptom

Cause

How to Manage

 

 

 

There is no IP

●The power of the camera

●Turn on the power.

address of your

is not turned on.

 

network camera

 

 

 

 

on The Camera

●LAN cable is not

●Connect the LAN cable of the camera to a hub or

Finder’s Network

connected.

router in the right way.

Camera List.

 

●Be sure to turn on the power of the hub and router.

 

 

 

 

●LAN cable is not

●Connect the LAN cable to the PC in the right way.

 

connected to the PC.

 

 

 

 

 

●IP address of the PC is

●Configure the IP address of your PC correctly.

 

not configured.

(→ page 23).

 

 

 

Cannot display a

●Installed directory of

●Assign the directory where you are going to install the

browser from

browser is wrong.

browser. Start Camera Finder and go to “View”/

Camera Finder.

 

“Customize”/“Default Browser.”

 

 

 

The message,

●The IP addresses of the

●Set the correct IP address of the network camera.

“The page

camera and your PC are

●Set the correct IP address of your PC.

cannot be

wrong.

 

displayed,”

 

 

 

 

shows up, and

●Proxy has set to the

●When proxy is set to the browser, sometimes you may

cannot login to

browser.

not able to login. Change the setting which will not via

the camera even

 

the IP address of the network camera from the proxy of

if you start

 

the browser, or the setting of host name which will not

Camera Finder.

 

via proxy.

 

 

 

Cannot login to

See “The message, ‘The page cannot be displayed,’ shows up, and cannot login to the

the camera even

camera even if you start Camera Finder.”

though entering

 

 

the IP address of

 

 

the camera

 

 

directly to the

 

 

browser, and

 

 

“The page

 

 

cannot be

 

 

displayed” shows

 

 

up.

 

 

 

 

 

Installation/Set up and OperationViewing

Recording

Setting up

Others

83

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Model IK-WR01A Important Safety Instructions Introduction Viewing and Operation IntroductionMonitor Out Connector Names and Features of PartsMode Setting Switch Lens Iris ADJ Line Lock Phase ADJEthernet Port Video Out JackInstallation/Setup Adjust the Angle of View InstallationTilt rotation Installation Recording Setting up Installing the Camera Unit46 mm Change of Dome Cover Dome replacementConnecting to a Video Monitor Connecting to a Video MonitorWhen power is supplied from a PoE compatible hub, etc About the Power Select SwitchWhen power is supplied from an AC24V or DC12V power source Line-Lock control Video Switcher CAMERA1Line Lock Phase Back Light Compensation Adjusting a LensMode Setting Switch Auto White Balance AWB Requirements for Network Camera Monitoring System Setting Up the Network Camera EnvironmentEntering an IP Address Manually About the IP AddressObtaining an IP address automatically from the Dhcp server Structure of Connection Set the IP address of the personal computer Connecting Connect a LAN cable and then turn the power onUsing Camera Finder to Search for a Camera Click the camera you want to login from the list of camerasSetting up Camera Finder Click Exit button to close Camera Finder Click the User buttonClick Admin on the left side of the screen Changing Administrator Login ID and PasswordClick the browser Click the Change buttonClick User on the left side of the screen Setting up Access RestrictionClick the Set/Change button Click Network on the left side of the screen Configuring the Network ManuallyClick the Save button Select ManuallyInstallation/Set up Viewing and Operation Close the browser to log off disconnect the camera ViewingViewing Images Camera Window Screen Menu that is displayed when right-clicking on the imageAdjusting Images on the Camera OperationViewing Adding Images Click View log on the left side of the Camera Window screen Viewing LogsOperationViewing Recording About Recording Images Recordable Media Recordable ContentsClick FTP client on the left side of the screen Recording Images on FTP ServerFTP General Settings Configure each setting itemsConnection to FTP Enable Click the Save Settings button below the settingPeriodic FTP by Schedule Configure recording scheduleEnter File Name FTP by Motion Detection Configure settings for viewing FTP status File Transfer Order Click Image Recording Setting up RecordingClick the Start button Recording Images on a Personal ComputerSpecify the destination folder and file name Click Save Current Picture AsRecording Setting up Configure each item How to Set upChanging the camera name System SettingsClick System on the left side of the screen Adjusting the date and time Setting up a format to display date/timeSetting the color of date/time display Changing the time using an NTP server settingUpdating the Firmware Rebooting the network cameraClick Export current configurations Importing the Settings Saved on a Personal ComputerDisplaying the screen asking a user name and password User SettingsDeleting a user name Storing the user name and passwordAdmin Settings Restarting the camera Changing the Administrator ID and passwordClick Alarm on the left side of the screen Alarm SettingsSetting the motion detection Setting the motion detectionConfiguring the connection Network SettingsFramerate Control Configuring the Http port numberDNS update to DNS 1/2 Server Click Mail on the left side of the screen Mail SettingsConfigure each item For details, refer to Recording Images on FTP Server → FTP Client SettingsClick Ddns on the left side of the screen Ddns SettingsBefore Starting Updating the FirmwareClick Upload button on the screen shown in Step Click Firmware updateClick the Browse button Specify the destination and then save the file Click Export current configurationsClick Import on the screen shown in Step Select the file on settings you savedSetting up Others Index Glossary Safety Precautions3Jpeg Up and OperationViewing Display of Logs Recording Setting up Before Calling Service Personnel Guide of your broadband router Before Calling Service Personnel...Symptom Cause How to Manage Cannot perform Lost the power RAM Sometimes primary is described as master Symptom Cause How to Manage Recorded Others IK-WR01A SpecificationsAppearance Diagram 150 Mounting Base BracketToshiba America Information SYSTEMS. INC
Related manuals
Manual 4 pages 31.62 Kb
Top Page Image Contents