Sharp MD-E9000H Basic Operation Setting the Clock, To check the time when the power is on

Page 14

Setting the

Basic Operation - Setting the Clock -

This may be operated only with the remote control.

In this example, the clock is set for the 24-hour (0:00) display.

1 Press the CLOCK button and within 10 seconds, press the MEMORY/ENTER button.

2 Press the 5/3 or 2/4 button to select 24-hour or 12-hour display and then press the MEMORY/ENTER button.

“0:00” → The 24-hour display will appear. (0:00 - 23:59)

“AM 0:00” → The 12-hour display will appear. (AM 0:00 - PM 11:59)

“AM 12:00” → The 12-hour display will appear. (AM 12:00 - PM 11:59)

3 Press the 5/3 or 2/4 button to adjust the hour and then press the MEMORY/ENTER button.

●When the 12-hour display is selected, “AM” will change automatically to “PM”.

4 Press the 5/3 or 2/4 button to adjust the minutes and then press the MEMORY/ENTER button.

●The hour will not advance even if minutes advance from “59” to “00”.

●The clock starts from “0” second. (Seconds are not displayed.)

To check the time when the power is on:

Press the CLOCK button.

The time display will appear for about 10 seconds.

Note:

The “0:00” or time will flash at the push of the CLOCK button when the AC power supply is restored after a power failure or unplugging the unit.

Readjust the clock by performing “Setting the Clock” from the beginning.

14	Web-site:www.sharp.co.uk/support Help Line: 08705 274277 (office hours)

*MD9000H-E12-14

14

2001.4.20, 2:05 AM

Image 14

Contents MD-E9000H Special Notes Special NotesContents General PrecautionsVolume control Care of compact discs AccessoriesGeneral Information Precautions / Accessories 7 8 9 10 11 12 13 16 17 Controls and IndicatorsGeneral Information Controls and Indicators Front panelDisplay Rear PanelControls and Indicators Remote ControlTweeter Woofer Bass Reflex Duct Speaker Terminals Speaker SystemSpeaker connection Placing the speaker systemAerial connection Connecting the AC power leadSystem Connections For Use ConnectionsTest of the remote control Remote ControlBattery installation Preparation for Use Remote ControlGeneral Control Demonstration modeTo turn the power on To change the display brightness 2 levelsBass control Adjusting the volumeSound Control EqualiserTo check the time when the power is on SettingBasic Operation Setting the Clock Press the CD 06 button to start playback from track Listening to a CDCD Playback Listening to a CD To interrupt playbackTo locate the desired portion Listening to a CDTo locate the beginning of a track Press the MD 06 button to start playback Listening to a MiniDiscMD Playback Listening to a MiniDisc Listening to a MiniDisc To remove a MiniDiscProgrammed Play Programmed PlayDirect Play Direct Play Repeat or Random PlayRepeat or Random Play Switching the display during MD playback Switching the DisplaySwitching the time display Advanced CD/MD Playback Switching the DisplayRadio Listening to the Radio Auto tuningListening to the Radio To receive an FM stereo transmissionTo recall a memorised station Listening to a Memorised StationMemorising a station To clear all memorised stationsInformation provided by RDS Using the Radio Data System RDSUsing Data System RDSRDS To erase all of the contents of preset memory Using the Radio Data System RDSUsing the Auto Station Programme Memory To stop the Aspm operation before it is completeIf you select the traffic programme To recall stations in memoryTo specify programmed types and select stations PTY search To cancel the EON stand-by mode EON-PTYTo automatically play the traffic information EON-TIAbout the TP and TA indicators MeaningAbout track numbers Before Recording to a MiniDiscDifferences from tape recordings Disc writing TOCMD Recording Recording to a MiniDisc from a CD Recording to a MiniDisc from a CDRecording to a MiniDisc from a CD One Touch Editing Load a CD and a recordable MiniDisc Press the REC button To record without using One-Touch EditingMD Recording Programmed recording from a CD Recording to a MiniDisc from a CDRecording the first several tracks of a CD Press the MD 06 button Recording to a MiniDisc from the RadioMD Recording Recording to a MiniDisc from the Radio To interrupt recordingMD Editing Titling a MiniDisc Titling a MiniDiscCreating disc and track names Press the MD button and load a MiniDisc seeMiniDiscaTitling To combine tracks Editing a Recorded MiniDiscTo divide a track MD Editing Editing a Recorded MiniDiscTo move a track To move programmed tracks programmed moveTo erase all of the tracks at once Editing a Recorded MiniDiscTo erase a track To erase programmed tracks programmed EraseAdvanced Features Timer and Sleep Operation Timer and Sleep OperationTimer playback/Timer recording To cancel the timer operation Timer and Sleep OperationTo confirm the timer setting Sleep operationSimultaneous sleep and timer operation To confirm the remaining sleep timeListening to the playback sounds from Connected device HeadphonesEnhancing Your Stereo System Recording on a MiniDiscWhat is a What is a MiniDisc?Helpful tip when attaching a label MiniDisc System LimitationsWhen an error message is displayed, proceed as follows Error MessagesError Messages CD player Troubleshooting ChartTroubleshooting Chart MiniDisc TunerMaintenance Troubleshooting ChartAmplifier SpecificationsSpecifications MiniDiscMemo Memo Sharp Corporation