Sharp MD-E9000H operation manual About the TP and TA indicators, Meaning

Page 30

Using the Radio Data System (RDS) (continued)

Radio

Data System (RDS) -

RDS

the Radio

 

- Using

■Notes for RDS operation

If any of the following events occur, it does not mean that the unit is faulty:

●“PS”, “NO PS” and a station name appear alternately, and the unit does not oper- ate properly.

●If a particular station is not broadcasting properly or a station is conducting tests, the RDS reception function may not work properly.

●When you receive an RDS station whose signal is too weak, information like the station name may not be displayed.

●“NO PS” or “NO PTY” will flash for about 5 seconds, and then the frequency will be displayed.

About the “TP” and “TA” indicators:

“TP”

“TA”

Meaning

 

 

 

Not lit

Not lit

Does not carry traffic announcements nor does it refer, via EON,

 

 

to a programme that does.

 

 

 

Not lit

Lit

Carries EON information about another programme which gives

 

 

traffic information.

 

 

 

Lit

Not lit

Carries traffic announcements but not at present and may also

 

 

carry EON information about other traffic announcements.

 

 

 

Lit

Lit

A traffic information is currently on air.

 

 

 

In the following cases, the EON stand-by mode will be cancelled.

●When you press the ON/STAND-BY button to enter the stand-by mode.

●When the unit is switched to another band in the EON stand-by mode.

●When you change the FM station whilst in the EON stand-by mode.

●When a preset call is made.

Notes:

●Whilst the same programme as the specified PTY (or TA) is being broadcast, the unit will not switch to an ON (other network) station.

●If there are more than two ON stations, compare the strength of signal and tune in to the station with the strongest signal (EON-AF). If an ON station has been stored in the preset channel memory, the unit will switch to that channel.

●If you want to leave an ON station tuned in by the EON and return to the station you were receiving, press the EON button.

●After the unit returns to the original station, the stand-by mode will still be active. (The “TI” or “PTY” will remain lit.)

●The unit does not switch between ON stations. It returns to the original station.

●If there is any problem with the ON station the unit switched to, “WEAK SIGNAL” will appear and the unit will return to the original station.

●If the signal from the ON station the unit switched to is very weak, the unit will search for another station with the strongest signal. However, if the signals from all stations are weak or not good (due to electrical noise), the unit displays “WEAK SIGNAL” and returns to the original station.

30

Web-site:www.sharp.co.uk/support Help Line: 08705 274277 (office hours)

 

*MD9000H-E24-30

30

2001.4.20, 2:11 AM

Page 29 Page 31
Image 30
Page 29 Page 31
Contents MD-E9000H Special Notes Special NotesContents Precautions Volume controlGeneral Accessories General Information Precautions / AccessoriesCare of compact discs 7 8 9 10 11 12 13 16 17 Controls and IndicatorsGeneral Information Controls and Indicators Front panelDisplay Rear PanelControls and Indicators Remote ControlTweeter Woofer Bass Reflex Duct Speaker Terminals Speaker SystemSpeaker connection Placing the speaker systemAerial connection Connecting the AC power leadSystem Connections For Use ConnectionsTest of the remote control Remote ControlBattery installation Preparation for Use Remote ControlGeneral Control Demonstration modeTo turn the power on To change the display brightness 2 levelsBass control Adjusting the volumeSound Control EqualiserSetting Basic Operation Setting the ClockTo check the time when the power is on Press the CD 06 button to start playback from track Listening to a CDCD Playback Listening to a CD To interrupt playbackListening to a CD To locate the beginning of a trackTo locate the desired portion Listening to a MiniDisc MD Playback Listening to a MiniDiscPress the MD 06 button to start playback Listening to a MiniDisc To remove a MiniDiscProgrammed Play Programmed PlayDirect Play Repeat or Random Play Repeat or Random PlayDirect Play Switching the display during MD playback Switching the DisplaySwitching the time display Advanced CD/MD Playback Switching the DisplayRadio Listening to the Radio Auto tuningListening to the Radio To receive an FM stereo transmissionTo recall a memorised station Listening to a Memorised StationMemorising a station To clear all memorised stationsInformation provided by RDS Using the Radio Data System RDSUsing Data System RDSRDS To erase all of the contents of preset memory Using the Radio Data System RDSUsing the Auto Station Programme Memory To stop the Aspm operation before it is completeTo recall stations in memory To specify programmed types and select stations PTY searchIf you select the traffic programme To cancel the EON stand-by mode EON-PTYTo automatically play the traffic information EON-TIAbout the TP and TA indicators MeaningAbout track numbers Before Recording to a MiniDiscDifferences from tape recordings Disc writing TOCRecording to a MiniDisc from a CD Recording to a MiniDisc from a CD One Touch EditingMD Recording Recording to a MiniDisc from a CD To record without using One-Touch Editing MD RecordingLoad a CD and a recordable MiniDisc Press the REC button Recording to a MiniDisc from a CD Recording the first several tracks of a CDProgrammed recording from a CD Press the MD 06 button Recording to a MiniDisc from the RadioMD Recording Recording to a MiniDisc from the Radio To interrupt recordingMD Editing Titling a MiniDisc Titling a MiniDiscCreating disc and track names Press the MD button and load a MiniDisc seeMiniDiscaTitling To combine tracks Editing a Recorded MiniDiscTo divide a track MD Editing Editing a Recorded MiniDiscTo move a track To move programmed tracks programmed moveTo erase all of the tracks at once Editing a Recorded MiniDiscTo erase a track To erase programmed tracks programmed EraseTimer and Sleep Operation Timer playback/Timer recordingAdvanced Features Timer and Sleep Operation To cancel the timer operation Timer and Sleep OperationTo confirm the timer setting Sleep operationSimultaneous sleep and timer operation To confirm the remaining sleep timeListening to the playback sounds from Connected device HeadphonesEnhancing Your Stereo System Recording on a MiniDiscWhat is a What is a MiniDisc?Helpful tip when attaching a label MiniDisc System LimitationsError Messages Error MessagesWhen an error message is displayed, proceed as follows CD player Troubleshooting ChartTroubleshooting Chart MiniDisc TunerMaintenance Troubleshooting ChartAmplifier SpecificationsSpecifications MiniDiscMemo Memo Sharp Corporation
Top Page Image Contents