TANDBERG D14041.02 manual Turning Power On or Off, Power On Mode, Power Off Mode, Standby Mode

Page 10

D14041.02 January 2008

TANDBERG FieldView Device User Guide

2.4. Turning Power On or Off

There are three power modes: On, Off and Standby

2.4.1. Power On Mode

Press and release the Power button to turn the FieldView Device on. When you first turn the camera on, you may be required to log in, and a touch panel calibration screen may appear.

When the power is on the Power indicator LED is green.

2.4.2. Power Off Mode

Turning off the FieldView Device automatically logs you out. To turn the

FieldView Device Off, press and hold the Power button for two seconds.

•If the FieldView Device was on, a message is displayed indicating that the FieldView Device is turning off. If a call was active a prompt appears, asking for confirmation to terminate the call.

•If the FieldView Device was in standby, it immediately switches off.

When the power is off the Power indicator LED is off.

2.4.3. Standby Mode

Standby mode provides longer battery life than Power On mode because it shuts down the display and puts the camera into a low power mode. However, incoming calls may still be received. To enter Standby mode, first turn the FieldView Device on, then press and release the Power button to enter Standby mode.

If a call was active a prompt is displayed asking for confirmation to terminate the call. A message is displayed indicating that the FieldView Device is entering Standby.

When the FieldView Device is in Standby mode, the Power indicator LED is green. This is the only visible indication that the FieldView Device is in Standby mode and is capable of receiving incoming calls.

To come out of Standby, press the Power button or answer an incoming call. If your site requires a log-in, you can answer a call but you must log in again before you can use the FieldView Device to stream video. A log-in screen is presented as soon as you do something that requires it.

The FieldView Device also enters Standby mode automatically after a configurable amount of time. To set this:

1.From the standard Viewfinder display window, press and release the Display button three times (or until the Main Menu appears).

2.Tap the Configuration option with the stylus to display the Configuration screen.

3.Display the General tab and set the time in the Standby Timeout field. Enter a time of ‘0’ to disable automatic Standby mode.

2.4.4.Resetting the FieldView Device (Soft Reset)

If the FieldView Device becomes non-responsive and you cannot turn it off by pressing the Power button for two seconds, a soft reset may be required. To reset the FieldView Device, press and hold both the Power and Display buttons until the display clears (approximately 10 seconds).

Do not perform a soft reset on the FieldView Device unless it stops responding to normal operations.

CAUTION:

A hard reset can be generated using the reset switch accessible through the access hole located near the SD memory card slot.

The hard reset should not be used by non-service personnel because

damage to the FieldView Device file system may result.

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents FieldView Device Contact information Table of Contents Technical Specifications Safety & Regulatory Information What’s in the Box FieldView DeviceAbout This Guide Share snapshot images betweenParts of the FieldView Device Button Function Menu Function Indicators Name ExplanationNavigation Pad Buttons Zoom/Manual Focus ControlsInserting or Replacing the Battery Charging the BatteryFieldView Device Basic Operation Calibrating the Integrated Touch Panel Power Off Mode Turning Power On or OffPower On Mode Standby ModeLogging on Logging On & OffInserting and Removing an SD Memory Card Logging off To log outAnswering an Incoming Call Network AccessAnswering & Initiating Calls Initiating Starting a CallVoIP Telephone Communication Audio/Video AV Functions Setting the Subject Audio SourceUsing S-video Turning the Video Stream On or OffAdjusting Zoom Levels FocusingSharing Images Telestration Drawing Lines on the ViewfinderCapturing Still Images Recording and Playing VideosPlaying a video recording Streaming a Video RecordingRecording a video To record a video Tap File PlaybackViewfinder Features & Display Modes Controlling the Viewfinder ModeMenus Stream SetupBandwidth or High Bandwidth, and then select Accept Managing Files Checking StatusViewing Local Contacts Session Folders and File NamesRename files and folders To rename a file or folder File Pane IconsIcon Description Tap Rename Play videosConfiguration Maintenance Tab Configuration Options ProvidedVersion Icons Connected to external power Audio volume increasedAudio volume decreased Stream initializingTandberg FieldView Device User Guide Display/Touch Screen Maintaining the FieldView DeviceGeneral Recommendations OpticsMPEG-4 Simple Profile @ L3 Technical SpecificationsSpecifications VGA 640 × 480 display/viewfinderSafety & Regulatory Information Industry Canada Class a Notice 001000 Safety NoticeFCC Class B Notice S/N 001100 and higher Industry Canada Class B Notice 001100 and higherMail tandberg@tandberg.com Tandberg FieldView Device User Guide Tandberg FieldView Device User Guide
Top Page Image Contents