JVC TK-C625 manual Operating Precautions, Install the unit on a strong and stable surface

Page 5

Introduction (continued)

EN 5

 

Operating Precautions

8WARNING

●Install the unit on a strong and stable surface.

This unit has been designed to revolve at high speed. Due to its weight (about 1.3 kg) and the vibrations it may be subjected to, the camera must be mounted to a sturdy and stable material. If the ceiling material lacks strength, for example if it is made of a decorative laminated material or plasterboard, then the mount should be reinforced using materials such as veneered plywood. If such reinforcement is inadequate, images may fluctuate due to vibration or, in the worst case, the camera may fall and cause a serious accident should there be anyone below it.

●For installation, use the provided ceiling mount and the optional flush mounted ceiling bracket, which is sold separately. When installing this device, the provided ceiling mount and the optional flush mounted ceiling bracket, which are sold separately should be used. Also be sure to connect the drop prevention wire and tighten all screws and nuts firmly.

●Power the unit with the rated power voltage. The power rating for this unit is 24 V AC, 50 Hz/60 Hz. If a power above this rating is supplied, a malfunction will occur or, in the worst case, smoke or fire may be produced.

●This unit offers a certain degree of protection against any damage either to itself or to its connection cable that might result from indirect lightning strikes, but it is not capable of preventing all damage by lightning strikes. For example it is not protected against a direct lightning strike. If lightning damage can be expected in the place where the unit is installed, be sure to take countermeasures by adding an arrester to the connection cable, etc.

●To save energy, turn the system off whenever it is not in use.

●This camera has been designed for indoor use. It cannot be used outdoors.

●This camera has been designed to be hung from a ceiling. Do not install it in an upright position on a surface or at an angle, as this may cause a malfunction or a noticeable shortening of its service life.

●Do not install or use the camera in the following locations.

•In a place exposed to rain or water.

•In a place containing vapor or oil soot, for example in a kitchen.

•In a place outside the operating temperature range (-10Ito 50I).

•Near a source of strong radio waves or magnetism, radiation or X-rays.

•In a place where corrosive gassed are generated.

•In a place subject to vibrations.

•In a place with excessive dust.

●Insufficient ventilation of the camera may cause a malfunction. Be careful not to block ventilation of the camera. This unit radiates heat from the panel surfaces (top panel and side panels). Do not install it in a place where a heat pool may form, such as near a wall.

●Do not install the camera in a place exposed to cold air, for example near to the air outlet of an air conditioner. Otherwise, moisture may become condensed inside the dome cover.

●Do not point the lens at a strong light source, for example under the sun. Doing so may cause the camera to malfunction.

●The camera incorporates an AGC circuit. As a result, when it is used under low light conditions the camera gain may increase automatically. This makes the picture appear uneven, however this is not a malfunction.

●When equipment that generates strong magnetism such as a transceiver is used near to the unit while the AGC circuit is ON, beat noise, etc may interfere with the picture. If a transceiver or similar equipment is used, keep it a distance of at least 3 meters from this unit.

●In auto iris mode, when the AGC circuit is ON, varying the iris with the iris control button may not change the picture brightness. This is due to the automatic gain boost by the AGC circuit. In this case, set AGC to OFF or use the manual iris mode.

●In auto iris mode, the iris control button may not function under certain brightness conditions (i.e. when a sufficient amount of light cannot be obtained). In this case, set the iris mode to manual.

●When the camera is used in ATW (Auto White balance) mode, the colors captured by the camera may differ from the actual colors being shot due to the mechanics of the auto- tracking operation within the white balance circuit. However, this is not a malfunction.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents For Customer Use Dome Type Camera TK-C625INSTRUCTIONSInformation Safety PrecautionsRisk of Electric Shock Do not Open Important Safeguards Contents CharacteristicsInstall the unit on a strong and stable surface Operating PrecautionsZooming operation Preset positionsName and Function of Parts Machine ID Machine ID Setting Switch Ceiling Mount Setting Switch Side CameraSetting Switch Auxiliary SwitchMulti-Drop Communication System Connections & Installation110 K Video SWITCHER, etcCAM2 Length of stub CAM32 Length of stub Switch 7 Invalid Set to OFF Switch 8 on Setting not RequiredPoint-to-Point Communication System ACable ConnectionsB a pg Terminal side of the Ceiling MountExample connection with an RM-P2580 DuplexSimplex Camera Controller RX + TX +Sync Switch SettingsProtocol That the number LL is correct Machine ID Setting SwitchDisplayed as ID- LL. Check Machine ID Installation Make a hole in the ceiling Connect the cable to this camera Cable ConnectionsRemove the Cover Lead the cable through the CoverRating Connecting an RG-59 coaxial cableConnect to an AC 24 V Supply Connect this to the remote control unit RM-P2580Connection Length ConductorFasten the ceiling mount to the ceiling Installing the Ceiling MountAttach the Safety Wire 20 EN Installing the CameraCheck that the Locking Screw is loosened Fit the camera to the ceiling mountSetting Up the Camera Using RM-P258021 Setup ProcedurePress and hold the Menu button for 3 seconds Press the SET button22 EN Menu Screen ConfigurationSetting Up the Camera Using RM-P2580 Private Mask Mode OFF Camera Function 2 Screen 24 ENCamera Function 1 Screen Tilt Limit AF for IRPAN Limit Auto Return26 EN Camera TITLE/ALARM ScreenCamera ALC/VIDEO Screen Auto PAN/PATROL/TRACE Screen 28 ENPOS. Function SET Screen 30 EN Factory Settings ScreenPrivate Mask Setup Select a camera. ARM-P2580AINSTRUCTIONSB Manual PAN Limit SetupMenu screen display. a pg , steps 2 to Set the position for the left limitBasic operation of Manual Pan Limit Settings that override the Manual Pan LimitOperations that override the Manual Pan Limit Right Limit Invalid RangeSelect the camera. a RM-P2580AINSTRUCTIONSB Camera Title SetupRepeat Steps 5 to Area Display Setup TitlePress the FAR button East Area Display Setup DirectionWest Direction Standard Axis ScreenRepeat steps 5 to 7 for each alarm title Alarm Title SetupAlarm Title Edit Screen Title input Field Camera buttonNNumeric keyCamera NumberNENTER buttonSet the Auto PAN Mode and Auto PAN Speed Auto PAN SetupSet the end position only when in the Return mode Select camera. ARM-P2580AINSTRUCTIONSBChange the Auto Patrol mode Auto Patrol SetupSet a patroll position Set the length of time a camera will stay in each positionAuto Trace Setup Select a preset position. a RM-P2580 Ainstructionsb Position Title SetupRepeat steps 5 to 7 for each title character Position buttonNNumeric key position numberNENTER buttonOther Troubleshooting42 EN External Dimensions Unit mm Ceiling Mount Hole Unit mm SpecificationsPan/Tilt Mechanism GeneralTK-C625 Dome Type Camera

TK-C625 specifications

The JVC TK-C625 is a compact yet highly effective industrial camera that has made a significant impact in various surveillance and monitoring contexts. Developed by JVC, a pioneer in video technology, the TK-C625 stands out for its impressive features, innovative technologies, and reliable performance.

At the heart of the TK-C625 is a high-resolution CCD sensor, which captures images with exceptional clarity and detail. With a resolution of 600 TV lines, this camera is adept at delivering sharp images even in challenging lighting conditions. This capability makes it suitable for a variety of environments, including retail spaces, educational institutions, and parking lots, where detail and accuracy are paramount.

One of the notable features of the TK-C625 is its effective low-light performance. Equipped with a built-in Automatic Gain Control (AGC) feature, the camera can enhance sensitivity in low-light environments, ensuring that quality footage can be captured even in dimly lit areas. This feature is crucial for security applications where monitoring takes place during nighttime hours.

In addition to its impressive imaging capabilities, the TK-C625 offers versatile mounting options. The compact design allows for a range of installation configurations, including wall, ceiling, or even desktop setups. The camera's lightweight build is also a plus, facilitating ease of installation without compromising on stability.

The JVC TK-C625 incorporates advanced signal processing technologies, providing enhanced image quality and reducing noise, which is particularly important in surveillance situations where clarity can mean the difference between identifying a suspect or missing critical details. Its electronic shutter technology allows for quick response to changing light conditions, improving its adaptability to various scenes and preventing overexposure.

Another significant aspect of the TK-C625 is its robust construction. Designed with durability in mind, the camera can withstand the rigors of consistent use in commercial settings, delivering reliable operation over long periods. This resilience is further complemented by its ease of use and maintenance, making it an ideal choice for businesses seeking dependable surveillance solutions.

Overall, the JVC TK-C625 is a high-performance camera that combines advanced features with user-friendly operation. Its high resolution, low-light capabilities, flexible installation, and durable design make it a standout option for surveillance professionals looking for quality and reliability in their monitoring solutions.
Top Page Image Contents