Ensure that the lock screw is loose, Fit the camera

JVC TK-C676 manual Ensure that the lock screw is loose, Fit the camera, Rotate the camera, Camera

Page 17

Ceiling Mount

Lock screw

Camera

2. Ensure that the lock screw is loose.

The camera cannot be attached properly if the lock screw of the Ceiling Mount is too tight.

Camera clamping bracket

3. Fit the camera.

Check the position of the camera clamping bracket and that of the lock screw, and fit the camera onto the ceiling mount.

4. Rotate the camera.

Make sure that the camera is horizontal, then turn the camera clockwise until it stops. Ensure that the camera- clamping bracket is in line with the lock screw of the Ceil- ing Mount.

Rotate the camera clockwise.

Lock screw

5. Tighten the lock screw.

Tighten the lock screw using a Phillips screwdriver.

CAUTION

If the lock screw is not tightened firmly, the camera may rattle or fall down. Be sure to tighten the lock screw firmly.

* To remove of the camera from the ceiling mount, reverse the steps1 to 5.

Tighten the lock screw.

Image 17

Contents

TK-C676 Important Safeguards Contents Provided Accessories FeaturesSafety Precautions Instructions Ceiling mount Preset positions Precautions for Correct OperationCamera setups with which auto focusing may be difficult Zooming Ceiling Mount Controls, Connectors and Indicators$ Machine ID Switch Camera Connector FemaleSetting Switches Connector MaleObserve the following points when connecting compo Switch settings PMulti-Drop Communication System Cable connections PMemo Terminal side of the Ceiling Mount Switch 7 OFF Switch 8 onPoint-to-Point Communication System Two wires must be connected Four wires must be connectedDuplex For example connection with an RM-P2580 Camera Setting switches Switch SettingsMachine ID Camera ID check procedureBers on the RM-P2580 ExampleMake a 90 mm diameter hole in the ceiling Cable ConnectionsConnect the cables Remove the cover from the Ceiling MountAttach the cover Attach the drop prevention wire Attaching a safety wireAttaching the Ceiling Mount Attaching the CameraFit the camera Ensure that the lock screw is looseRotate the camera Tighten the lock screwSetting the camera menus from an RM-P2580 Setup ProcedurePress and hold the Menu button for 3 seconds Press the SET buttonMenu for setting up the function of each preset position Menu for setting up the home posi- tion onlyMenu Screen Flow Normal screenCamera Function Screen Camera TITLE/ALARM Screen Alarm Alarm Input PolarityAlarm Output Alarm OUT1Camera ALC/ExDR screen Camera Video Adjustment ScreenExDR Mode AGC Mode10 dB Sense UPMode ColourLevel LOWHome Motion Detect Screen Alarm DisplayArea Edit DemonstrationAuto PAN/PATROL/TRACE Screen Position Function SET Screen Factory Settings screenPrivate Mask Setup Repeat steps 5 and 6 for each title character Camera Title SetupPress the Tele button Move the cursor to Area Title Edit and press the SET button Area Title SetupPress the FAR button Repeat steps 5 to 7 for each area titleRepeat steps 5 to 7 for each alarm title Alarm Title SetupDisplay the Setup menu on the camera Move the cursor to Area Edit and press the SET button Home Motion Detect SetupHome Motion Detect menu Area Edit screenAdjust the viewing angle of the start position Auto PAN SetupSet the auto pan mode and speed Auto Patrol Setup Move the cursor to Autotrace SET and press the SET button Auto Trace SetupSet the patrol start position Auto Trace SET screen is displayedRepeat steps 5 to 7 for each title character Position Title SetupPosition Function SET screen Position Title screenCeiling plate Attaching a Ceiling Flush Mount Bracket Optional WB-S575Clamp the Ceiling Flush Mount Bracket Connection Cables Attach the Ceiling Mount to the Ceiling Flush Mount BracketAttach the ceiling panel Remove the ceiling panel Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the camera Check the release labels thoroughly before removalSymptom Cause Information Remedy TroubleshootingPower cannot be Turned onCamera SpecificationsPan/Tilt Mechanism GeneralDimensions in combination with the WB-S575 External dimensions Unit mmCeiling mount hole WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C676 Dome Type Camera

Related manuals

JVC TK-C676 manual Ensure that the lock screw is loose, Fit the camera, Rotate the camera, Camera