JVC TK-C676 manual Controls, Connectors and Indicators,  Ceiling Mount

Page 6

Introduction

Controls, Connectors and Indicators

Ceiling Mount

0

Cover

98 7 6

1

2

5

 

 

3 4

(Connector side)

9Pin(CN24)1 of alarm output terminal

8Pin 1 of CONTROL terminal (CN22)

7Pin 1 of ALARM I/O terminal (CN23)

6Pin 1 of alarm input terminal (CN26)

(Terminal Pin Layout)

1[VIDEO OUT] Coaxial Cable Connectors

Output connector of a composite video signal (1 V(p-p)) with an output impedance of 75 Ω, to be connected to a switcher, etc.

2[AC ` 24V INPUT] Connector

Connect to a 24 V AC power supply.

3Cover Position Alignment Mark

When attaching the cover, use this mark to align its final position correctly.

7[ALARM I/O] Input/Output Terminals (CN23)

Terminals for Alarm input 1 and Alarm output 1. ☞ P. 15

Pin No.

Signal Name

1Alarm output 1 (N.OPEN)

2Alarm output 1 (COM)

3Alarm output 1 (N.CLOSE)

4Alarm input 1

5

GND

4Locking Screw

Tighten this screw to fasten the camera clamping bracket

*.

5Safety Wire Hole

To prepare for possible dropping of the camera, pass the wire from the ceiling slab or channel through this hole.

6Alarm Input Terminals (CN26)

Input terminals for Alarm 2, Alarm 3 and Alarm 4.

Connect the provided cables to these terminals. ☞ P. 15

Pin No.

Signal Name

Color of Cable

1

Alarm input 2

Brown

2

GND

Red

3

Alarm input 3

Orange

4

GND

Yellow

5

Alarm input 4

Violet

6

GND

Gray

 

 

 

8[CONTROL] Terminals (CN22)

Connect to a RM-P2580 remote control unit.

Pin No.

Signal Name

Mark

1

TX +

A

 

 



2

TX –

B

 

 



3

RX +

C

 

 



4

RX –

D

 

 



9Alarm Output Terminals (CN24)

Output terminals for Alarm 2 and Alarm 3.

Connect the provided cables to these terminals. ☞ P. 15

Pin No.

Signal Name

Color of Cable

1

Alarm output 2 +

Red

2

Alarm output 2 –

White

3

Alarm output 3 +

Orange

4

Alarm output 3 –

Gray

 

 

 

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents TK-C676 Important Safeguards Contents Safety Precautions FeaturesProvided Accessories Instructions Ceiling mountCamera setups with which auto focusing may be difficult Precautions for Correct Operation Preset positions  ZoomingControls, Connectors and Indicators  Ceiling MountSetting Switches Camera Connector Female$ Machine ID Switch Connector MaleMulti-Drop Communication System Switch settings PObserve the following points when connecting compo Cable connections PMemo Switch 7 OFF Switch 8 on Point-to-Point Communication SystemTerminal side of the Ceiling Mount Duplex Four wires must be connectedTwo wires must be connected For example connection with an RM-P2580 CameraSwitch Settings  Setting switchesBers on the RM-P2580 Camera ID check procedureMachine ID ExampleConnect the cables Cable ConnectionsMake a 90 mm diameter hole in the ceiling Remove the cover from the Ceiling MountAttach the cover Attaching the Ceiling Mount Attaching a safety wireAttach the drop prevention wire Attaching the CameraRotate the camera Ensure that the lock screw is looseFit the camera Tighten the lock screwPress and hold the Menu button for 3 seconds Setup ProcedureSetting the camera menus from an RM-P2580 Press the SET buttonMenu Screen Flow Menu for setting up the home posi- tion onlyMenu for setting up the function of each preset position Normal screenCamera Function Screen Camera TITLE/ALARM Screen Alarm Output Alarm Input PolarityAlarm Alarm OUT1Camera Video Adjustment Screen Camera ALC/ExDR screen10 dB AGC ModeExDR Mode Sense UPLevel ColourMode LOWArea Edit Alarm DisplayHome Motion Detect Screen DemonstrationAuto PAN/PATROL/TRACE Screen Factory Settings screen Position Function SET ScreenPrivate Mask Setup Camera Title Setup Press the Tele buttonRepeat steps 5 and 6 for each title character Press the FAR button Area Title SetupMove the cursor to Area Title Edit and press the SET button Repeat steps 5 to 7 for each area titleAlarm Title Setup Display the Setup menu on the cameraRepeat steps 5 to 7 for each alarm title Home Motion Detect menu Home Motion Detect SetupMove the cursor to Area Edit and press the SET button Area Edit screenAuto PAN Setup Set the auto pan mode and speedAdjust the viewing angle of the start position Auto Patrol Setup Set the patrol start position Auto Trace SetupMove the cursor to Autotrace SET and press the SET button Auto Trace SET screen is displayedPosition Function SET screen Position Title SetupRepeat steps 5 to 7 for each title character Position Title screenAttaching a Ceiling Flush Mount Bracket Optional WB-S575 Clamp the Ceiling Flush Mount BracketCeiling plate Attach the Ceiling Mount to the Ceiling Flush Mount Bracket Attach the ceiling panelConnection Cables Remove the camera Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the ceiling panel Check the release labels thoroughly before removalPower cannot be TroubleshootingSymptom Cause Information Remedy Turned onPan/Tilt Mechanism SpecificationsCamera GeneralCeiling mount hole External dimensions Unit mmDimensions in combination with the WB-S575 WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C676 Dome Type Camera
Related manuals
Manual 216 pages 55.17 Kb Manual 48 pages 62.15 Kb

TK-C676 specifications

The JVC TK-C676 is a professional-grade CCTV camera renowned for its impressive image quality and reliable performance in various surveillance applications. As part of JVC's reputable line of security products, the TK-C676 incorporates advanced technologies that make it a popular choice among security professionals and businesses alike.

One of the standout features of the TK-C676 is its high-resolution imaging capability. With a 1/3-inch CCD sensor, this camera delivers crisp and clear images, ensuring optimal visibility even in challenging lighting conditions. The camera offers a resolution of 540 TV lines, which allows for detailed surveillance footage that can be crucial for identifying individuals or activities in monitored areas.

Another notable characteristic of the TK-C676 is its robust low-light performance. Thanks to its sense-up technology, the camera can automatically adjust its sensitivity in low-light environments, providing better image quality without the need for external lighting. This feature is particularly valuable for nighttime surveillance or in dimly lit indoor settings, enhancing the overall effectiveness of security measures.

The TK-C676 also excels in flexibility and adaptability with its mechanical IR cut filter. This technology allows for seamless switching between day and night modes, ensuring consistent image quality during both daytime and nighttime operation. This adaptability makes the camera suitable for various applications, including retail stores, parking lots, and public spaces.

Additionally, the JVC TK-C676 features a varifocal lens with a focal length of 3.5mm to 8mm, providing users with the ability to adjust the field of view based on specific surveillance needs. This versatility enables the camera to cover wide areas or focus on particular subjects, making it ideal for both indoor and outdoor placements.

In terms of durability, the TK-C676 is built to withstand harsh environmental conditions. With a sturdy housing that resists both water and dust, this camera can be installed in various locations without compromising on performance. This reliability is essential for continuous operation in demanding environments.

Overall, the JVC TK-C676 is a well-rounded CCTV camera that offers high-resolution imaging, excellent low-light performance, and adaptable features. Its combination of advanced technology, durable construction, and flexible camera options makes it a strong choice for anyone seeking a reliable surveillance solution. Whether for commercial, industrial, or residential applications, the TK-C676 proves to be a valuable asset in enhancing security measures.
Top Page Image Contents