JVC GR-DVL210 14 EN, Basic Recording, To Stop Recording, To Adjust The Brightness Of The Display

Page 14

14 EN

Power lamp

Power Switch

During

Lock Buttonshooting Recording Start/Stop Button

Display

2 5min Tape remaining time indicator (Approximate)

min 90 min 89 min 3 min

(Now calculating)

0 min 1 min 2 min

(Blinking) (Blinking) (Blinking)

BR I GHT

MENU/BRIGHT Wheel

180° 90°

PUSH-OPEN

Button

Tally lamp (lights while recording is in progress)

BASIC RECORDING

Basic Recording

NOTE:

You should already have performed the procedures listed below. If not, do so before continuing.

●Power ( pg. 7)

●Grip Adjustment ( pg. 9)

●Viewfinder Adjustment ( pg. 9)

●Load A Cassette ( pg. 11)

●Recording Mode Setting ( pg. 12)

1 Press in the tabs on the lens cap to remove it.

2 Set the Power Switch to “ ” or “ ” while pressing down the Lock Button located on the switch.

Shooting while using the LCD monitor: Make sure the LCD monitor is fully open. Tilt it upward/ downward for best viewability.

Shooting while using the viewfinder: Close the LCD monitor.

•The power lamp lights and the camcorder enters the Record-Standby mode. “PAUSE” is displayed.

3 Press the Recording Start/Stop Button. “” appears while recording is in progress.

To Stop Recording . . .

.... press the Recording Start/Stop Button. The camcorder

re-enters the Record-Standby mode.

To Adjust The Brightness Of The Display

.... rotate the MENU/BRIGHT wheel until the bright level

indicator on the display moves and the appropriate brightness is reached.

NOTES:

●If the Record-Standby mode continues for 5 minutes, the camcorder’s power shuts off automatically. To turn the camcorder on again, set the Power Switch to “OFF”, then back to “” or “ ”.

●The image will not appear simultaneously on the LCD monitor and the viewfinder. It will appear in the viewfinder when the LCD monitor is in the lock position, and it will appear on the LCD monitor when fully extended.

●When a blank portion is left between recorded scenes on the tape, the time code is interrupted and errors may

occur when editing the tape. To avoid this, refer to “Recording from the middle of a tape” ( pg. 17).

●To turn the tally lamp or beep sounds off, pg. 31, 33.

For other notes, pg. 51

Image 14

Contents GR-DVL210 Dear Customer It is recommended that youSafety Precautions Remote Control Unit RM-V715U BN-V408U AAA R03 Battery x Lens Cap pgHow To Attach The Lens Cap Automatic DemonstrationContents Getting StartedTo Detach The Battery Pack PowerCharging the Battery Pack Slide BAT. Release and pull out the battery packAbout Batteries Using the Battery PackUsing AC Power Selection in the AC range from 110 V to 240Shoulder Strap Attachment Grip AdjustmentViewfinder Adjustment Tripod MountingDate/Time Settings 10 ENLoading/Unloading a Cassette Approximate recording time12 EN Recording Mode SettingSet the tape recording mode depending on your preference Contents Basic Recording & PlaybackBasic Recording To Adjust The Brightness Of The Display14 EN Basic RecordingJournalistic Shooting Operation ModePower Switch Position Manual SELF-RECORDINGZoom Slide the Power Zoom Lever towards T16 EN Zoom OutProper recording When a blank portion is recorded on a tapeTime Code Basic To Control The Speaker Volume18 EN Normal PlaybackPress Blank Search To cancel Blank Search midwayBlank Search 20 EN If using a VCR . . . go to step If not . . . go to step EN21Advanced Features 22 ENSnapshot Snapshot Mode SelectionFor Recording Snapshot RecordingNight-Alive To Deactivate The Selected Mode24 EN Program AE With Special EffectsSlow Slow Shutter Gives recorded scenes a strobe effectYour recording looks like a series of consecutive snapshots FADE/WIPE Selection 26 ENFade/Wipe Effects Picture Wipe or Dissolve SelectionFader And Wipe Menu Menu Effect28 EN Feature Auto FocusFeature Manual Focus To obtain correct focusExposure Control Iris LockManual White Balance Operation White Balance Adjustment30 EN To Return To Automatic White BalanceIf you have selected WIPE/FADER Program AE or W. Balance Using Menus for Detailed AdjustmentFor Recording Menu System or DisplayMenu Screen Explanations Recording. Also to activate the shutter sound effect pg Normal screen ratioScreen ratio becomes When the Power Switch is set from OFF to or Does not reset all settings to the factory-presetResets all settings to the factory-preset When the date is changed during video playbackFollowing procedure applies to all except Synchro Comp pg For Playback MenuPlayback Sound DisplayDubbing Dubbing To a VCR38 EN To use this camcorder as a playerInstalling The Battery RM-V700U, optional Using the Remote Control UnitInstalling The Batteries RM-V715U, provided Using the Remote Control Unit 40 ENFeature Playback Zoom Press Play 4 to find the scene of interestSET REMOTE/VCR Code 42 ENRandom Assemble Editing R.A.Edit VCR Recording deckVCR other than above JVC VCR equipped with a remote pause connectorMake Connections 44 EN Select ScenesAutomatic Editing to VCR For More Accurate Editing Adjustment of VCR/CAMCORDER Timing46 EN Diagnosing VCR/CAMCORDER TimingTo hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen pgAudio Dubbing AUsing PC connection cable Using PC connection cableUsing DV cable Using DV cableConnection To a Video Unit Equipped With a DV Connector 50 EN References pg PowerDetails Corrective Action Clean the lens and check52 EN Replace with new cassetteEN53 Troubleshooting 54 ENEN55 56 EN Turn off the camcorder User MaintenanceAfter Use Cleaning The Camcorder Press Push Here to close the cassette holder58 EN 5 6 @ # $Monitor Open Button Push Open pg Audio/Video Output Connector pg , 37Power Lamp pg Focus Button pg60 EN LCD Monitor/Viewfinder Indications During RecordingBright Displays the brightness of the LCD Displays the sound modeLCD Monitor/Viewfinder Indications During Playback Indications Function Temperature Range Specifications 64 EN Declaration of Conformity Model Number About moisture condensationSerious malfunctioning Trade Name66 EN TermsFor General SpecificationsFor Connectors For Digital Video CameraGR-DVL210