JVC GR-SXM47 To Detach The Battery Pack, Slide Battery Release and pull out the battery pack

Page 6
Make sure the battery pack is attached to the camcorder. Hook its end to the camcorder 1 and push the battery in until it locks in place 2.
•If the battery pack is attached in the wrong position, a malfunction may occur.
Set the Power Switch to “OFF”. Connect the AC Adapter to the camcorder 3, then connect the Power Cord to the AC Adapter 4.
Plug the Power Cord into an AC outlet 5. The CHARGE lamp on the camcorder blinks to indicate charging has started.

6EN

Hook on.

Power

GETTINGSTARTED

1

2 Push in.

BATTERY RELEASE Switch

REFRESH Button

REFRESH Lamp

CHARGE Lamp

Battery pack

Power Switch

 

To AC outlet

3 To DC IN

 

connector

5

 

4

AC Adapter

 

Battery pack

Charging time

BN-V11U*

approx. 1 hr. 30 min.

BN-V12U (optional)

approx. 1 hr. 30 min.

BN-V20U** (optional)

approx. 2 hrs. 20 min.

BN-V400U (optional)

approx. 4 hrs. 30 min.

* GR-FXM37/FX12 only

**Provided with GR-SXM47/SX22 only.

This camcorder’s 2-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

1

2

3

4 When the CHARGE lamp stops blinking but stays lit, charging is finished. Unplug the Power Cord from the AC outlet. Disconnect the AC Adapter from the camcorder.

To Detach The Battery Pack . . .

.... slide BATTERY RELEASE and pull out the battery pack.

NOTES:

●During charging or discharging, the camcorder cannot be operated.

●Charging and discharging is not possible if the wrong type of battery is used.

●When charging the battery pack for the first time or after a long storage period, the CHARGE lamp may not light. In this case, remove the battery pack from the camcorder, then try charging again.

●If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.

●Using the optional AA-V15EK AC Power Adapter/ Charger, you can charge the BN-V11U/V12U/V20U/ V400U battery pack without the camcorder. However, it cannot be used as an AC adapter.

REFRESH:

Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure below to fully discharge the battery pack before recharging.

1.Perform steps 1 through 3 of “CHARGING THE BATTERY PACK”.

2.Press REFRESH on the camcorder for over 2 seconds. The REFRESH lamp on the camcorder blinks to indicate discharging has started.

3.When discharging is finished, charging automatically starts and the CHARGE lamp blinks.

When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing because leaving a battery with some charge left over also reduces performance.

For other notes, ☞ pg. 35

Page 5 Page 7
Image 6
Page 5 Page 7
Contents GR-SXM47 GR-SX22 GR-FXM37 GR-FX12 It is recommended that you Connection to the mains supply in the United KingdomEN3 Do not block the ventilation holesPower Cord Battery Pack AC Adapter AP-V10EG Lens Cap Cable AdapterShoulder Strap Core Filter x How To Attach The Core Filter How To Attach The Lens CapEN5 To Detach The Battery Pack Slide Battery Release and pull out the battery packApproximate recording time unit min Perform of Charging the Battery Pack pgEN7 Use the AC Adapter connect as shown in the illustrationTripod Mounting Grip AdjustmentViewfinder Adjustment Shoulder Strap AttachmentDate/Time Settings Comes onRotate Menu to select Recording Format Setting 10 ENEN11 RecordingPlaybackRegular VHS VCR Recording Mode Setting Tape Length SettingLoading/Unloading a Cassette EN13To Stop Recording 14 ENShooting While Watching The LCD Monitor Models equipped with LCD monitor onlyEN15 SELF-RECORDING models equipped with LCD monitor only16 EN Slide the Power Zoom Lever towards TSlide the Power Zoom Lever towards W ZoomEN17 5Sec. Rec 5-Sec. RecordingFor the next shot Basic Features Set Light OFF/AUTO/ON as required OFF Turns off the lightRecording Advanced Features EN19 Fade/Wipe EffectsFades in/out to a black screen 20 EN Program AE With Special EffectsDigital Effects EN21EN Recording Advanced Features Using Menus For Detailed AdjustmentIf you select Jlip ID no Allows you to superimpose one of eight preset titles pg Refer to Focusing pgAdjustment This Menu Screen cannot be accessed while recordingAdvanced Features 24 ENSystem Menu Date/Time Insert Instant TitlesTime-Lapse Set REC Time and 2 of Animation aboveSet the Power Switch to Press MENU. The Menu Screen appears Exposure ControlEN27 Focusing 28 ENPatterns that are regularly repeated EN29 White Balance AdjustmentManual White Balance Operation Press Menu again to close the Menu ScreenLoad a tape pg Set the Power Switch to 30 ENRotate Bright towards + to brighten, or towards to darken Playback Features EN31 Use the provided Cable Adapter If your TV/VCR has a 21-pin connectorBasic Connections And Tape Dubbing CamcorderTape Dubbing Power supply instead of the battery pack pgBasic Connections EN3334 EN Cassette Adapter optionalAs necessary before you start shooting When the Power Switch is set to or and the LCD monitor isViewfinder switches off automatically to save power models Equipped with LCD monitor onlyRecording does not start No power is suppliedRecording cannot be performed Animation or Time-Lapse is notLens CAP warning indicator may blink when An error number i.e. E03 appearsThat Date/Time setting is carried out Lens CAP warning indicator38 EN Use only the following batteryTo prevent damage and prolong service life To avoid hazardEN39 To prevent damage to the LCD monitor, do not To prolong service lifeCleaning The Camcorder About moisture condensationEN41 42EN 3 4 5 t y @ # $ %EN43 44 EN Indications During RecordingIndications TBC Indicator Recording Format Indicator S/S-ET Indications During PlaybackEN45 46 EN Memo EN47 Victor Company of JAPAN, Limited
Top Page Image Contents