Panasonic PV-GS320 operating instructions Setting date and time, About date/time

Page 17

Before using

ªHow to turn the power on and off with

the LCD monitor/viewfinder

When the power switch is set to [ON], the power can be turned on and off with the LCD monitor and the viewfinder when the unit is in Tape Recording Mode or Card Recording Mode.

OFF

ON

1Open the LCD monitor out or extend the viewfinder to use. (-18-)

≥The LCD monitor or viewfinder will be activated.

2Close the LCD monitor and retract the viewfinder.

OFF

ON

≥The power will not turn off unless the LCD monitor is closed and the viewfinder is retracted.

≥The Status indicator automatically goes off and the power turns off. (If quick start is set to [ON] (-19-), the unit goes into quick start standby mode and the Status indicator lights green.)

≥The power does not turn off even if the

LCD monitor is closed and the viewfinder is retracted while recording on a tape.

3Open the LCD monitor or extend the viewfinder to turn the power on and use the Camcorder again.

OFF

ON

≥The Status indicator lights red and the power turns on.

Setting date and time

When the Camcorder is turned on for the first time, [SET DATE AND TIME] will appear.

≥Select [YES] and press the center of the joystick. Perform steps 2 and 3 below to set the date/time.

If the screen shows the incorrect date/time, then adjust it.

≥Set to Tape Recording Mode or Card

Recording Mode.

1Set [BASIC] >> [CLOCK SET] >> [YES]. (-24-)

2Move the joystick left or right in order to select the item to be set. Then move the joystick up or down to set the desired value.

≥The year will change as follows: 2000, 2001, ..., 2089, 2000, ...

≥The 12-hour clock is used.

3Press the joystick to determine the setting.

≥The clock function starts at [00] seconds.

ªAbout date/time

≥The date and time function are driven by a built- in lithium battery.

≥Make sure to check the time before recording.

ªRecharging the built-in lithium battery

≥If [0] or [--] is appears when the Camcorder is turned on, then the built-in lithium battery has run down. Use the steps below to charge the battery. When turning on the power for the first time after charging, [SET DATE AND TIME] will appear. Select [YES] and set the date and time. Connect the AC adaptor to the Camcorder or attach the battery to the Camcorder and the built-in lithium battery will be recharged. Leave the Camcorder as is for approx. 24 hours and the battery will drive the date and time for approx. 6 months. (Even if the [OFF/ON] switch is set to [OFF], the battery is still being recharged.)

17

LSQT1091

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operating Instructions Thank you for choosing Panasonic Following mark and symbols are located on bottom of the unitFollowing Applies only in the U.S.A Important Safety Instructions Button-type battery Lithium battery Battery pack Lithium ion battery packThis AC adaptor operates on AC between 110V and 240 But Button-type batteryBattery pack Article 8 Termination of License Before opening the CD-ROM package, please read the followingContents Edit mode Playback modeWith a PC MenuQuick Guide Recording on a tape How to turn off the powerRecording still pictures onto a card Photoshot Playing back tapeCamcorder AccessoriesParts identification and handling USB terminal -50-,-52 DC input terminal DC/C.C.IN Viewfinder -18 Adjust the belt length and the pad position How to remove the Sensor tag for U.S.A. only Attaching the lens cap Grip beltConnecting to the AC outlet Power supplyRemoving the battery Charging lampWhile pressing the button 1, set the OFF/ on switch to on How to turn on the power≥Set the OFF/ON switch to OFF when not using the Camcorder Charging time and recordable timeAbout date/time Setting date and timeRecharging the built-in lithium battery Using the viewfinder Using the LCD monitorAdjusting the field of view Extending the viewfinderSet Setup Quick Start OFF To cancel Quick StartQuick Start Open the LCD monitor or extend the ViewfinderWhen the cassette holder cannot be Housed When the cassette holder does not Come outInserting/removing a cassette Inserting/removing a cardCard access lamp Selecting a modeConcerning the write protection Switch on the SD Card Concerning the cardTape recording mode AUTO/MANUAL/FOCUS switch is set to Auto How to use the joystickBasic joystick operations Joystick and screen displayTo exit the Help mode Help modeSlide show start/pause Delete Playback the next pictureUsing the menu screen Switching the languageAbout the menu setting To exit the menu screenOperating with remote control Adjusting LCD monitor/viewfinderAdjusting the brightness and color Level Order to increase the brightness Entire LCD monitorInstall a button-type battery Using the remote controlRemote control Concerning the button-type battery Remote control usable rangeSelecting the remote control mode Recording mode About auto modeCheck before recording Basic Camcorder positioningPowersave On-screen display in the tape recording modeRecording on a tape Concerning the remaining tape time Indication on the screenBlank search function Recording checkStopping blank search midway Through Set Advanced Picturesize select the desired picture sizeRecording still pictures onto a card Photoshot On-screen display in the card recording modeTo record still pictures clearly Select the size of still pictures to be recorded on a cardZoom in/out function Concerning the focusing areaSelect the picture quality for Photoshot images Recording with a shutter operation EffectBacklight compensation function Recording yourselfTo cancel the MagicPix function Soft skin modeTo cancel the soft skin mode MagicPix functionTo cancel fading To cancel the tele macro functionTele macro function Fade in/fade out functionTo cancel Auto Ground-Directional Standby To cancel the wind noise reduction FunctionWind noise reduction function Auto Ground-Directional Standby AGSTo stop the timer midway through Self-timer recordingTo Cancel the Wide/43 Function Wide/43 functionTo cancel the optical image stabilizer Function Recording in various situations Scene modeTo Cancel the Guideline Function Optical image stabilizer functionRecording in natural colors White balance To cancel the scene mode functionTo restore to the automatic Adjustment About the black balance adjustment Manual focus adjustmentTo set the white balance manually About flashing of the indicationTo restore to automatic adjustment Manual shutter speed/aperture adjustmentShutter speed range Iris/gain value rangeSettings on the audio To adjust volumePlaying back tape Repeat playbackSlow-motion playback/ frame-by-frame playback Press the E button or the D button on the remote controlVariable-speed search function To return to normal playbackTo display the on-screen information On the TV Playback on TVPlaying back card To display multiple playback files Deleting files recorded on a cardAbout the compatibility of still pictures To delete all filesProtecting files on a card Writing the printing data on a card Dpof settingFormatting a card Copying onto a DVD recorder or a VCR Dubbing Recording from a tape onto a cardUsing the DV Interface Cable for Recording Digital Dubbing You can add music or narration to the recorded cassette To cancel the standby for recordingAudio dubbing PC Connection With DV Interface Cable ≥Set to Tape Recording ModeBefore recording with audio dubbing To play back the sound recorded with Audio dubbingWhen you stop printing halfway Check before Use Using the Camcorder with a PCSoftware Installation Using the Built-in SD Drive Connecting Computer CamcorderOperating environment For WindowsOperating environment Using as a Web cameraInstalling USB Driver Set Advanced USB Function WEB CAM Setting up Windows MessengerUsual operation WEB Camera mode Tape Playback Mode Click Sign Type in your Sign-in name and password Setting up MSN Messenger Windows Live MessengerType in your E-mail address and password Case of MSN MessengerSound Using Quick Movie Magic or MotionDV StudioHard disk Necessary software DirectX 9.0b/9.0cTo start Quick Movie Magic or MotionDV Studio Installation of Quick Movie Magic MotionDV StudioClick the Quick Movie Magic/ MotionDV Studio Click Next Click FinishIf a description other than Microsoft is displayed ≥Update the driver with the following procedureClick Update Driver To disconnect USB cable safely Using on MacintoshOperating environment on iMovie IMovie HD Copying still pictures on PCWith a PC ≥When Camcorder power is turned OFF If you no longer need software or driver Uninstall≥When Mode Dial is turned to change modes When using on MacintoshFiles recorded on a SD Card About the SD CardAbout the compatibility of the card Files Tape Recording Menu Menu listTape Playback Menu MenuCard Playback Menu Card Recording MenuAdvanced O.I.S. -38-GUIDE Lines -38-SHTR Effect Basic DATE/TIME -65-PROTECTOther menus Menus related to taking picturesMenus related to playback Basic indications IndicationsRecording indications Playback indicationsTextual indications Confirmatory indicationsThere is no ink. Check the connected printer Functions that cannot be used simultaneouslyThere is no paper. Check the connected printer Check the connected printerBefore requesting repair Problems and solutions Cassette cannot be inserted Original sound was erased when audio dubbing was performedAuto focus function does not work Camcorder arbitrarily stops recordingCard Recorded pictures are not clear Push the Reset Switch is displayedPhotoshot playback images do not look Normal Even if a card is formatted, it cannot be usedAbout the Camcorder About condensationAbout dirty heads Be sure to detach the battery after use About the batteryPrepare spare batteries when going out for recording Do not throw old battery into fireAbout the cassette About the AC adaptorAbout the card Folder structure of the cardPeriodical check-ups Explanation of termsAutomatic white balance LCD monitorAuto focus White balanceHttp//panasonic.co.jp/pavc/global/cs SpecificationsMode Accessory# Description Camcorder Accessory SystemVisa Camcorder Accessory Order Form For USA CustomersRequest for Service Notice USA Only Request for Service NoticePanasonic Video Products Limited Warranty For USA CustomersAccessory Purchases Customer Services DirectoryCentralized Factory Service Center Npcparts@us.panasonic.comPanasonic Canada Inc Warranty For Canadian CustomersAmbler Drive, Mississauga, Ontario L4W 2T3 Camcorder Product One 1 year, parts and labourNumerics IndexSpanish Quick Use Guide Guía española para el uso rápido Grabación en una cinta Cómo apagar la alimentaciónGrabación de imágenes fijas en una Tarjeta Photoshot Reproducción de la cintaF1106Ak0
Top Page Image Contents