Panasonic PV-GS320 To cancel Quick Start, Open the LCD monitor or extend the Viewfinder

Page 19

Before using

Quick Start

When Quick Start is ON the battery power is still being consumed, even when the LCD Monitor and the Viewfinder are closed.

The Camcorder will resume recording/pause mode about 1.7 seconds after the LCD Monitor and the Viewfinder are reopened.

≥Please note in Quick Start Mode approximately half the pause recording power is being consumed.

Using Quick Start Mode will reduce the battery recording/playback time.

≥This is only activated in the following cases. ≥While using the battery

A tape or a card is inserted, while the Tape Recording Mode is set.

A card is inserted, while the Card Recording Mode is set.

≥While using the AC adaptor

Quick Start can be used even if a tape/card is not inserted.

≥Set to Tape/Card Recording Mode.

1Set [SETUP] >> [QUICK START] >> [ON].

(-24-)

2While the [OFF/ON] switch is still set to [ON], close the LCD monitor and retract the Viewfinder.

OFF

ON

≥The Status indicator lights green and the unit goes into quick start standby mode.

≥The Camcorder will not go into quick start standby mode unless the LCD monitor is closed and the viewfinder is retracted.

3Open the LCD monitor or extend the Viewfinder.

OFF

ON

≥The Status indicator lights red and the Camcorder is put into recording pause approx. 1.7 seconds after it is turned on.

ª To cancel Quick Start

1 Set [SETUP] >> [QUICK START] >> [OFF].

(-24-)

≥If the [OFF/ON] switch is set to [OFF] while the unit is in quick start standby mode, the power turns off.

≥If the standby continues for approx. 30 minutes, then the Status indicator will go off and the Camcorder will be completely turned off.

≥In the following cases, quick start is canceled and the power turns off.

≥When the Mode dial is moved.

≥When the battery or AC adaptor is removed. ≥When both the tape and card are removed while using the battery in Tape Recording

Mode.

≥When the card is removed while using the

battery in Card Recording Mode.

≥When the Camcorder is quick-started with the white balance on automatic, it may take some time until the white balance is adjusted if the scene being recorded has a light source different from the scene last recorded. (When the MagicPix function is used, however, the white balance of the scene last recorded is retained.)

≥If the power is turned on in quick start standby mode, the zoom magnification becomes 1t and the picture size may differ from what it was before quick start standby.

≥If [POWER SAVE] (-29-) is set to [5 MINUTES] and the unit automatically goes into quick start standby mode, set the [OFF/ON] switch to [OFF], then to [ON] again. Also, close the LCD monitor and retract the viewfinder and then open the LCD monitor or extend the viewfinder again.

19

LSQT1091

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operating Instructions Thank you for choosing Panasonic Following mark and symbols are located on bottom of the unitFollowing Applies only in the U.S.A Important Safety Instructions Button-type battery Lithium battery Battery pack Lithium ion battery packBattery pack Button-type batteryThis AC adaptor operates on AC between 110V and 240 But Article 8 Termination of License Before opening the CD-ROM package, please read the followingContents Menu Playback modeEdit mode With a PCQuick Guide Playing back tape How to turn off the powerRecording on a tape Recording still pictures onto a card PhotoshotParts identification and handling AccessoriesCamcorder USB terminal -50-,-52 DC input terminal DC/C.C.IN Viewfinder -18Grip belt How to remove the Sensor tag for U.S.A. onlyAdjust the belt length and the pad position Attaching the lens capCharging lamp Power supplyConnecting to the AC outlet Removing the battery Charging time and recordable time How to turn on the power While pressing the button 1, set the OFF/ on switch to on ≥Set the OFF/ON switch to OFF when not using the CamcorderRecharging the built-in lithium battery Setting date and timeAbout date/time Extending the viewfinder Using the LCD monitorUsing the viewfinder Adjusting the field of viewOpen the LCD monitor or extend the Viewfinder To cancel Quick StartSet Setup Quick Start OFF Quick StartInserting/removing a card When the cassette holder does not Come outWhen the cassette holder cannot be Housed Inserting/removing a cassetteConcerning the card Selecting a modeCard access lamp Concerning the write protection Switch on the SD CardJoystick and screen display How to use the joystickTape recording mode AUTO/MANUAL/FOCUS switch is set to Auto Basic joystick operationsPlayback the next picture Help modeTo exit the Help mode Slide show start/pause DeleteTo exit the menu screen Switching the languageUsing the menu screen About the menu settingOrder to increase the brightness Entire LCD monitor Adjusting LCD monitor/viewfinderOperating with remote control Adjusting the brightness and color LevelRemote control Using the remote controlInstall a button-type battery Selecting the remote control mode Remote control usable rangeConcerning the button-type battery Basic Camcorder positioning About auto modeRecording mode Check before recordingConcerning the remaining tape time Indication on the screen On-screen display in the tape recording modePowersave Recording on a tapeSet Advanced Picturesize select the desired picture size Recording checkBlank search function Stopping blank search midway ThroughSelect the size of still pictures to be recorded on a card On-screen display in the card recording modeRecording still pictures onto a card Photoshot To record still pictures clearlyRecording with a shutter operation Effect Concerning the focusing areaZoom in/out function Select the picture quality for Photoshot imagesBacklight compensation function Recording yourselfMagicPix function Soft skin modeTo cancel the MagicPix function To cancel the soft skin modeFade in/fade out function To cancel the tele macro functionTo cancel fading Tele macro functionAuto Ground-Directional Standby AGS To cancel the wind noise reduction FunctionTo cancel Auto Ground-Directional Standby Wind noise reduction functionWide/43 function Self-timer recordingTo stop the timer midway through To Cancel the Wide/43 FunctionOptical image stabilizer function Recording in various situations Scene modeTo cancel the optical image stabilizer Function To Cancel the Guideline FunctionTo restore to the automatic Adjustment To cancel the scene mode functionRecording in natural colors White balance About flashing of the indication Manual focus adjustmentAbout the black balance adjustment To set the white balance manuallyIris/gain value range Manual shutter speed/aperture adjustmentTo restore to automatic adjustment Shutter speed rangeRepeat playback To adjust volumeSettings on the audio Playing back tapeTo return to normal playback Press the E button or the D button on the remote controlSlow-motion playback/ frame-by-frame playback Variable-speed search functionPlaying back card Playback on TVTo display the on-screen information On the TV To delete all files Deleting files recorded on a cardTo display multiple playback files About the compatibility of still picturesFormatting a card Writing the printing data on a card Dpof settingProtecting files on a card Copying onto a DVD recorder or a VCR Dubbing Recording from a tape onto a cardUsing the DV Interface Cable for Recording Digital Dubbing Audio dubbing To cancel the standby for recordingYou can add music or narration to the recorded cassette To play back the sound recorded with Audio dubbing ≥Set to Tape Recording ModePC Connection With DV Interface Cable Before recording with audio dubbingWhen you stop printing halfway Software Installation Using the Camcorder with a PCCheck before Use For Windows Connecting Computer CamcorderUsing the Built-in SD Drive Operating environmentInstalling USB Driver Using as a Web cameraOperating environment Usual operation WEB Camera mode Tape Playback Mode Setting up Windows MessengerSet Advanced USB Function WEB CAM Case of MSN Messenger Setting up MSN Messenger Windows Live MessengerClick Sign Type in your Sign-in name and password Type in your E-mail address and passwordNecessary software DirectX 9.0b/9.0c Using Quick Movie Magic or MotionDV StudioSound Hard diskClick Finish Installation of Quick Movie Magic MotionDV StudioTo start Quick Movie Magic or MotionDV Studio Click the Quick Movie Magic/ MotionDV Studio Click NextClick Update Driver ≥Update the driver with the following procedureIf a description other than Microsoft is displayed Copying still pictures on PC Using on MacintoshTo disconnect USB cable safely Operating environment on iMovie IMovie HDWhen using on Macintosh If you no longer need software or driver UninstallWith a PC ≥When Camcorder power is turned OFF ≥When Mode Dial is turned to change modesAbout the compatibility of the card Files About the SD CardFiles recorded on a SD Card Menu Menu listTape Recording Menu Tape Playback MenuBasic DATE/TIME -65-PROTECT Card Recording MenuCard Playback Menu Advanced O.I.S. -38-GUIDE Lines -38-SHTR EffectMenus related to playback Menus related to taking picturesOther menus Playback indications IndicationsBasic indications Recording indicationsTextual indications Confirmatory indicationsCheck the connected printer Functions that cannot be used simultaneouslyThere is no ink. Check the connected printer There is no paper. Check the connected printerBefore requesting repair Problems and solutions Camcorder arbitrarily stops recording Original sound was erased when audio dubbing was performedCassette cannot be inserted Auto focus function does not workEven if a card is formatted, it cannot be used Push the Reset Switch is displayedCard Recorded pictures are not clear Photoshot playback images do not look NormalAbout dirty heads About condensationAbout the Camcorder Do not throw old battery into fire About the batteryBe sure to detach the battery after use Prepare spare batteries when going out for recordingFolder structure of the card About the AC adaptorAbout the cassette About the cardLCD monitor Explanation of termsPeriodical check-ups Automatic white balanceAuto focus White balanceHttp//panasonic.co.jp/pavc/global/cs SpecificationsMode Accessory# Description Camcorder Accessory SystemVisa Camcorder Accessory Order Form For USA CustomersRequest for Service Notice USA Only Request for Service NoticePanasonic Video Products Limited Warranty For USA CustomersNpcparts@us.panasonic.com Customer Services DirectoryAccessory Purchases Centralized Factory Service CenterCamcorder Product One 1 year, parts and labour Warranty For Canadian CustomersPanasonic Canada Inc Ambler Drive, Mississauga, Ontario L4W 2T3Numerics IndexSpanish Quick Use Guide Guía española para el uso rápido Reproducción de la cinta Cómo apagar la alimentaciónGrabación en una cinta Grabación de imágenes fijas en una Tarjeta PhotoshotF1106Ak0
Top Page Image Contents