Setting menus
AUTO SW screen
Item/ | Description of settings | |
(display mode) | ||
| ||
|
| |
|
| |
A. IRIS | ON: | |
(Camera) | When the AUTO button is pressed, the | |
| auto iris control operation is performed. | |
| The IRIS button does not work at this | |
| time. | |
| OFF: | |
| The auto iris control operation is not | |
| performed even if the AUTO button is | |
| pressed. | |
| The iris control operation selected by the | |
| IRIS button is performed. | |
|
| |
AGC | For setting the auto gain control operation | |
(Camera) | when ON is selected as the A. IRIS item | |
| setting. | |
| 6 dB: | |
| Auto gain control up to 6 dB is performed | |
| when the AUTO button is pressed. | |
| 12 dB: | |
| Auto gain control up to 12 dB is | |
| performed when the AUTO button is | |
| pressed. | |
| OFF: | |
| Auto gain control is not performed even | |
| if the AUTO button is pressed. | |
ATW | ON: | |
(Camera) | The ATW (auto tracking white balance) | |
| function operation is set to ON or OFF | |
| using the AUTO button. | |
| At this time, the operation of this function | |
| cannot be set to ON or OFF using the | |
| WHITE BAL switch and USER button. | |
| However, when ATWLOCK is allocated | |
| to the USER button, the white balance | |
| value can be fixed using the USER | |
| button. | |
| OFF: | |
| The ATW function operation is not | |
| performed even if the AUTO button is | |
| pressed. | |
| The ATW function operation selected by | |
| the WHITE BAL switch is performed. | |
|
| |
AF | ON: | |
(Camera) | When the AUTO button has been | |
| pressed, the auto focus operation is | |
| performed. | |
| The FOCUS switch and PUSH AUTO | |
| button do not work at this time. | |
| OFF: | |
| The auto focus operation is not | |
| performed even if the AUTO button is | |
| pressed. | |
| The focus operation selected by the | |
| FOCUS switch and PUSH AUTO button | |
| is performed. | |
|
|
PLAYBACK FUNCTIONS screen
Item/ | Description of settings | ENGLISH |
| ||
(display mode) |
| |
|
| |
|
|
|
|
|
|
END SEARCH | For setting what kind of operation is to be |
|
(VCR) | performed when the EVF DTL/END |
|
| SEARCH button is pressed. |
|
| BLANK: |
|
| The unrecorded blanks on the video tape |
|
| are searched. |
|
| REC END: |
|
| The part which was shot last is |
|
| searched. |
|
| <Notes> |
|
| O Even when the REC END setting is |
|
| selected, the part which was shot last |
|
| will not be searched when the tape is |
|
| switched. |
|
| O If nothing has been recorded on the |
|
| tape, operation will stop at the end of the |
|
| tape. |
|
| O END SEARCH may not operate properly |
|
| if there is an unrecorded blank near the |
|
| tape start or at a point along the tape. |
|
|
|
|
32K (12bit) | For setting the sound to be output as the |
|
AUDIO | CH1 and CH2 signals when a tape |
|
(VCR) | recorded in the 32K |
|
| played back. |
|
| ST1: |
|
| The sound recorded during shooting is |
|
| selected. |
|
| CH1 signals = CH1 track |
|
| CH2 signals = CH2 track |
|
| ST2: |
|
| The sound recorded during audio |
|
| dubbing is selected. |
|
| CH1 signals = CH3 track |
|
| CH2 signals = CH4 track |
|
| MIX: |
|
| The sound recorded during shooting and |
|
| the sound recorded during audio |
|
| dubbing are mixed. |
|
| CH1 signals = CH1 + CH3 tracks |
|
| CH2 signals = CH2 + CH4 tracks |
|
| <Note> |
|
| If the sound has been recorded in the 48K |
|
|
| |
| Therefore, the correlation between the |
|
| signals and tracks will always be as follows: |
|
| CH1 signals = CH1 track |
|
| CH2 signals = CH2 track |
|
|
|
|
The underlining indicates the factory setting.
43 (E)