Axis Communications Q1932E Advanced, Install PTZ Driver, Control Queue, Device Settings, Controls

Page 23

AXIS Q1932–E PT Mount Thermal Network Camera

PTZ (Pan Tilt Zoom)

Advanced

Device Settings

The Device Settings window displays driver specific settings. The appearance of this window can vary depending on the driver installed. Options that can be configured include:

•Driver Specific Settings for Video Source

•Mechanical Limits for Moving Video Source

•Extended Driver Specific Settings for Video Source

For download and installation information about PTZ drivers for your Axis product please visit www.axis.com/techsup/

Controls

Advanced PTZ settings can be configured under PTZ > Advanced > Controls.

The Panel Shortcut Command Buttons list shows the user-defined buttons that can be accessed from the Live View page’s Ctrl panel. These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command button.

The following PTZ controls are enabled by default:

•Pan control

•Tilt control

To disable specific controls, deselect the options under Enable/Disable controls.

Install PTZ Driver

This Axis product supports several PTZ devices. Please see www.axis.com for a complete list of supported devices, and to obtain the correct driver. To install a PTZ device you need to install the PTZ driver.

To install the PTZ driver go to PTZ> Driver Selection. Browse to find the driver (e.g. driver.ptz) and Upload. If the driver was successfully uploaded, it appears in the Select driver to use drop-down list. From this drop-down list, select the driver to install or remove, and click Save.

Select Activate PTZ to enable PTZ. The address of the connected device appears against Device ID. Choose the Device type from the drop-down list. To find which device type to use, consult the documentation supplied by the PTZ driver.

To complete the installation go to System Options > Ports & Devices > COM Port (see COM Port) and verify the settings.

Control Queue

The administrator can set up a queue for PTZ controllers from PTZ > Control Queue. Once set up, the PTZ Control Queue buttons appear in the Live View page offering one viewer exclusive control for a limited period of time. Other users will be placed in queue.

A user who belongs to a group (see Users on page 36) with a higher PTZ priority can go before other users in the queue and take control of the product. The order of priority is as follows:

1.Administrator — An administrator takes over PTZ control regardless of who is first in queue. The administrator will be removed from the queue 60 seconds after the last PTZ control command.

2.Event — The Axis product can be configured to go to a preset position when triggered by an alarm (see Events on page 31). The event will immediately be placed first in the queue except when an administrator is in control.

3.Operator — Same as administrator but with lower priority

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Axis Q1932-E PT Mount Thermal Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis Q1932-E PT Mount Thermal Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Connectors and ButtonsNetwork Connector SD Card Slot LED IndicatorsPower Connector RS485/RS422 ConnectorSet the Root Password Access the ProductAccess from a Browser Access from the InternetClick Use Https Go to Setup EventsLive View Controls on the Live ViewPTZ Controls Axis Media Control viewer toolbarAxis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream Axis Q1932-E PT Mount Thermal Network Camera Basic Setup Set Up the ProductImage VideoVideo Stream Pixel Counter264 Stream ProfilesImage Appearance Camera SettingsExposure Settings OverlayGo to Video Overlay Image Overlay ImageUse Overlay Text in an Action Rule Go to Events Action Rules Under Overlay Settings, select Include textPrivacy Mask Browser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsUser Defined Links Guard Tour Preset PositionsPTZ Pan Tilt Zoom Control Queue Install PTZ DriverDevice Settings AdvancedAxis Q1932-E PT Mount Thermal Network Camera Motion Detection Set Up Motion Detection WindowsDetectors Shock DetectionLow level 0% Default valuesParameter Object Size History Sensitivity High level 100% Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Cross Line Detection Install Axis ApplicationConfigure Axis Cross Line Detection Axis Video Motion Detection Configure Axis Video Motion DetectionAxis Q1932-E PT Mount Thermal Network Camera Go to Events Action Rules and click Add Setting Up an Action RuleEvents Add RecipientsGo to Events Schedules and click Add Set Up RecurrencesSet Up Email Recipients Create SchedulesAxis Q1932-E PT Mount Thermal Network Camera Go to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardCOM Port MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis Q1932-E PT Mount Thermal Network Camera Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserStorage and disk management problems Problems with streaming H.264Video and image problems, general Video Camera SettingsVideo cannot be recorded Technical Specifications Power Function/group Specifications Network SecurityInstallation Maintenance General CasingConnectors Function Pin RS485/422 ConnectorPerformance Considerations M3.3

Q1932E specifications

Axis Communications, a leading provider of network video solutions, offers a range of advanced surveillance cameras designed to meet the needs of various security applications. Among their innovative products is the Axis Q1932E, a robust thermal network camera that excels in challenging environments where visibility is compromised.

The Q1932E is particularly valued for its ability to detect and monitor objects and people in complete darkness, smoke, fog, or adverse weather conditions. This capability stems from its thermal imaging technology, which detects heat emitted by objects rather than relying on visible light. As a result, users can achieve reliable surveillance across different lighting conditions, making it ideal for critical applications like perimeter security, transportation, and infrastructure monitoring.

One of the main features of the Axis Q1932E is its resolution. The camera offers a thermal resolution of 384x288 pixels, allowing for detailed thermal imaging. This resolution is crucial for identifying potential threats even from a distance. The built-in digital Pan-Tilt-Zoom (dPTZ) capability allows users to zoom in on specific areas of interest, enhancing monitoring efficiency without losing sight of the broader scene.

Durability is another key characteristic of the Q1932E. It is designed with a weatherproof casing, complying with the IP66 standard, ensuring it can withstand harsh weather conditions such as rain, wind, and fluctuating temperatures. This rugged design makes it suitable for outdoor installations in various environments.

The camera also features Axis' advanced video analytics capabilities, enabling motion detection and edge analytics. These functionalities allow users to receive real-time alerts and notifications when unusual activity is detected, enhancing response times to potential security threats. The integration of Axis’ Zipstream technology further optimizes bandwidth and storage usage, reducing costs while maintaining high-quality video streams.

Installation is made convenient with Power over Ethernet (PoE) support, which allows both data and power to be delivered through a single cable, simplifying the setup process. Additionally, the camera supports various mounting options, providing flexibility to adapt to different surveillance needs.

In summary, the Axis Q1932E thermal network camera is a powerful tool for security professionals seeking to enhance their surveillance capabilities. With its superior thermal imaging, durability, advanced analytics, and ease of installation, it is an excellent choice for ensuring safety and security in any environment, regardless of the lighting conditions.
Top Page Image Contents